Electronic Connector JINJIA XLR-04WP-1 XLR Jack with Temperature Range Minus 30 to Plus 80 Degrees

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification applies to XLR jack connectors used in electronic products. It details the electrical, mechanical, durability, and environmental performance characteristics of the product.

Product Attributes

Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
Origin: China
Model Type: XLR JACK

Technical Specifications

Item	Property	Test Condition	Performance
2. Rated /	Practical temperature range	-30 to +80	N/A
	Humidity range	85% RH.MAX.	N/A
	Preservation temperature range	-10 to +40	N/A
	Humidity range (Preservation)	85% RH.MAX.	N/A
	Storage Condition	Around air without acid, alkaline or other corrosive gases. Storage period not exceed 180 days.	N/A
	Rated voltage and current (MAX.)	50V AC , 6A	N/A
	Appearance	No scratches, soil, rust or discoloration on the surface.	N/A
3. Construction /	Outline And Dimension	Should match the attachment drawing.	N/A
	Part And Material	Should be consistent with the material list specifications.	N/A
4. Electrical efficiency /	Withstand Voltage	Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur.	N/A
	Insulation Resistance	Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	10000 M Min.
	Contact Resistance	Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA).	30 m MAX.
5. Mechanical Performance	Insertion and withdrawal forces	Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. Insertion: 35 N max. Withdrawal: 2 N min.	N/A
	Terminal Strength	Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. There is no looseness, damage, etc., but the terminal deformation is acceptable.	N/A
6. Durability /	Life test	Under the condition of no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	Appearance no obvious change, destruction. Contact resistance: less than 50 m.
7. Solderability /	Resistance to soldering heat	The jack terminal should be dipped in solder. Temperature of solder: 2603. Dip time: 51 seconds. After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base.	N/A
	Solderability	Temperature of solder: 2453C. Time of dip: 30.5 seconds. Coating of solder area should be more than 95%.	N/A
8. Environment test /	Cold test	Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test.	Appearance no obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Heat test	The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	N/A
	Humidity test	The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	Appearance no obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Temperature Cycling	Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes.	N/A
	Salt spray test	Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry it at room temperature after the experiment.	Appearance no obvious rust.
9. Test condition /	Standard Test Conditions	Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. For judgment doubts: 201C, relative humidity 63% to 67%, air pressure: 86 kPa to 106 kPa.	N/A
10. Amendment /	Amendment Process	Amendments require negotiation and agreement by the manufacturer and the customer.	N/A