XLR Jack Connector JINJIA XLR-18-2-N3B Suitable for Electronic Products Requiring Durable Connectors

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR Jack Specification

This specification applies to XLR jacks used in electronic products. It details the electrical, mechanical, durability, and environmental performance characteristics of the XLR jack manufactured by Shenzhen Jinjiarun Electronic Technology Co., Ltd.

Product Attributes

Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
Origin: China
Model Type: XLR JACK

Technical Specifications

Section	Item	Property	Test Condition	Performance
2. Rated /	Practical temperature range			-30 to +80
	Humidity range			85% RH.MAX.
	Preservation temperature range			-10 to +40
	Humidity range (Preservation)			85% RH.MAX.
	Storage Environment			Without Acid Alkaline Or Other Corrosive Airs. Storage Period Not Exceed 180 Days.
	Rated voltage and current (MAX.)			50V AC, 6A
	Appearance			No scratches, soil, rust or discoloration on the surface.
4. Electrical efficiency /	Withstand Voltage		Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur.
	Insulation Resistance		Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	10000 M Min.
	Contact Resistance		Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA).	30 m MAX.
5. Mechanical Performance	Insertion and withdrawal forces		Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device.	Insertion: 35 N max. Withdrawal: 2 N min.
	Terminal Strength		Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds.	No looseness, damage, etc., but terminal deformation is acceptable.
6. Durability /	Life test		Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	Appearance: No obvious change, destruction. Contact resistance: less than 50 m.
7. Solderability /	Resistance to soldering heat		The jack terminal should be dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds.	After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base.
	Solderability		Temperature of solder: 2453C. Time of dip: 30.5 seconds.	Coating of solder area should be more than 95%.
8. Environment test /	Cold test		Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test.	Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Heat test		The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test.
	Humidity test		The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Temperature Cycling		Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes.
	Salt spray test		Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry it at room temperature after the experiment.	Appearance: No obvious rust.
9. Test condition /	Standard conditions		Test and measurement temperature is between 15C and 35C, relative humidity is between 25% and 85%, atmospheric pressure is between 86 kPa and 106 kPa.
	Doubtful conditions		201C, relative humidity is 63% to 67%, and air pressure is 86 kPa to 106 kPa.