electronic connector JINJIA XLR-16AP-N3B suitable for temperature range minus 30 to plus 80 degrees

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR JACK SPECIFICATION

This specification applies to XLR jacks used in electronic products. These connectors are designed for reliable performance in various electronic applications.

Product Attributes

Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
Origin: China
Document Number: JJR-WI-47
Issue Date: 2008-09-10
Version: A1

Technical Specifications

Category	Item	Property	Test Condition	Performance
Rated /	Practical temperature range	-30 to +80
	Humidity range	85% RH.MAX.
	Preservation temperature range	-10 to +40	Humidity range: 85% RH.MAX. (No Acid Alkaline Or Other Corrosive Airs, Storage Period Not Exceed 180 Days)
	Rated voltage and current(MAX.)	50V AC , 6A
Construction /	Outline And Dimension	Appearance and dimensions should match the attachment drawing.
Construction /	Part And Material	Parts and materials should be consistent with the material list specifications.
Electrical efficiency /	Withstand Voltage	Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur.	Between two non-contact terminals	No dielectric breakdown
	Insulation Resistance	10000 M Min.	Apply 500V DC between any contactless terminal and the other terminal for 1 minute 5 seconds.	10000 M Min.
	Contact Resistance	30 m MAX.	Measure the tail end of each terminal (voltage max 20mV, current max 100mA) of a pair of matched terminals.	30 m MAX.
Mechanical Performance	Insertion and withdrawal forces	Insertion: 35 N max. Withdrawal: 2 N min.	Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device.
Mechanical Performance	Terminal Strength	No looseness, damage, etc., but terminal deformation is acceptable.	Each terminal should withstand a force of 0.5 kgf for 10 seconds.
Durability /	Life test	Appearance no obvious change, destruction. Contact resistance: less than 50 m.	Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.
Solderability /	Resistance to soldering heat	Plastic base should not be deformed and terminals should not fall off the plastic base.	Dipped in solder at 2603 for 51 seconds.
Solderability /	Solderability	Solder area coating should be more than 95%	Solder temperature: 2453C. Time of dip: 30.5 seconds.
Environment test /	Cold test	Appearance no obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.	Place housing for 96 hours at -30 3 C. Then, place under standard atmospheric conditions for 1 hour and test.
	Heat test		Store housing at 802 for 96 hours. Then subject to standard atmospheric conditions for 1 hour and test.
	Humidity test	Appearance no obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.	Store housing at 403 with relative humidity of 90% ~ 95% for 96 h. Then subject to standard atmospheric conditions for 1 hour and test.
	Temperature Cycling		Place the Jack under specified conditions and then place in stand at room temperature for 30 minutes.
	Salt spray test	No obvious rust in appearance.	Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after experiment.
Test condition /		Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. (For judgment doubts: 201C, 63% to 67% RH, 86 kPa to 106 kPa)
Amendment /		Amendments require negotiation and agreement between manufacturer and customer.