Durable electronic connector JINJIA XLR-25W-N3B rated voltage 50V AC and current 6A for performance

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR Jack Specification

This specification applies to XLR jacks used in electronic products. The product is designed for a practical temperature range of -30 to +80 and a humidity range of 85% RH.MAX. It has a rated voltage and current of 50V AC and 6A respectively. The appearance should be free from scratches, soil, rust, or discoloration.

Product Attributes

Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
Origin: China
Document Number: JJR-WI-47
Issue Date: 2008-09-10
Version: A1

Technical Specifications

Item	Property	Test Condition	Performance
Rated /	Practical temperature range		-30 to +80
Rated /	Humidity range		85% RH.MAX.
Preservation Temperature	Range		-10 to +40
Preservation Temperature	Humidity range		85% RH.MAX.
Rated voltage and current(MAX.)			50V AC , 6A
Appearance			No scratches, soil, rust or discoloration on the surface.
Electrical efficiency /	Withstand Voltage /	Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute	No dielectric breakdown shall occur.
Electrical efficiency /	Insulation Resistance /	Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	10000 M Min.
Contact Resistance /		Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA)	30 m MAX.
Mechanical Performance /	Insertion and withdrawal forces /	Rate of insertion/withdrawal: 2 mm/s	Insertion: 35 N max. Withdrawal: 2 N min.
Mechanical Performance /	Terminal Strength /	Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds.	There is no looseness, damage, etc., but the terminal deformation is acceptable.
Durability /	Life test /	Under the condition of no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	Contact resistance: less than 50 m. Appearance: No obvious change.
Durability /	Resistance to soldering heat /	Temperature of solder: 2603. Dip time: 51 seconds.	After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base.
Solderability /	Solderability /	Temperature of solder: 2453C. Time of dip: 30.5 seconds.	Coating of solder area should be more than 95%
Environment test /	Cold test /	Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test.	Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Heat test /	The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test.
	Humidity test /	The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Salt spray test /	Temperature: 35 2 Solution: 5 1% Spray time: 24 hours	No obvious rust in the appearance.
Test condition /		Unless otherwise specified, the test and measurement temperature is between 15 C and 35 C, the relative humidity is between 25% and 85%, and the atmospheric pressure is between 86 kPa and 106 kPa.