High Durability JINJIA XLR-19P-11P XLR Jack Combo Connector with Corrosion Resistant Surface

Name: High Durability JINJIA XLR-19P-11P XLR Jack Combo Connector with Corrosion Resistant Surface
Brand: Hefei Purple Horn E-Commerce Co., Ltd.

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR JACK (Combo) SPECIFICATION

This specification applies to XLR jack (Combo) which is used in electronic products.

Product Attributes

Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
Origin: Shenzhen
Document Number: JJR-WI-46
Issue Date: 2008-09-10
Version: A1

Technical Specifications

Item	Property	Test Condition	Performance
2. Rated /
Practical temperature range	-30 to +80
Humidity range	85% RH.MAX.
Preservation temperature range	-10 to +40
Preservation humidity range	85% RH.MAX.	Surrounding air without acid, alkaline or other corrosive gases. Storage period not exceeding 180 days.
Rated voltage and current (MAX.)	50V AC , 3A (Type A)		7.5A (Type B)
Appearance			No scratches, soil, rust or discoloration on the surface.
4. Electrical efficiency /
Withstand Voltage		Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur.
Insulation Resistance		Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	10000 M Min.
Contact Resistance		Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA).	30 m MAX.
5. Mechanical Performance /
Insertion and withdrawal forces		Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device.	XLR: Insertion: 35 N max. Withdrawal: 2 N min. JACK: Insertion: 40 N max. Withdrawal: 5 N min.
Terminal Strength		Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds.	No looseness, damage, etc., but terminal deformation is acceptable.
6. Durability /
Life test		Under no load condition, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	Appearance no obvious change, destruction. Contact resistance: less than 50 m.
7. Solderability /
Resistance to soldering heat		The jack terminal should be dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds.	After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base.
Solderability		Temperature of solder: 2453C. Time of dip: 30.5 seconds.	Coating of solder area should be more than 95%.
8. Environment test /
Cold test		Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test.	Appearance no obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
Heat test		The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test.
Humidity test		The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	Appearance no obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
Temperature Cycling		Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes.
Salt spray test		Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry it at room temperature after the experiment.	Appearance no obvious rust.
9. Test condition /
General conditions		Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. For doubtful judgments: 201C, relative humidity 63% to 67%, air pressure: 86 kPa to 106 kPa.
10. Amendment /
Specifications amendment		Must be negotiated and agreed by the manufacturer and the customer before proceeding.
12. XLR JACK (Combo) TYPE / XLR
Type A
Type B