Electronic XLR jack JINJIA XLR-04W featuring no surface scratches rust or discoloration for long term

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification applies to XLR jack connectors used in electronic products. It details the electrical, mechanical, durability, and environmental performance characteristics of the XLR jack, ensuring reliable connectivity in various applications. The product is designed for practical operation within specified temperature and humidity ranges.

Product Attributes

Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
Origin: China
Model Type: XLR JACK

Technical Specifications

Section	Item	Property	Test Condition	Performance	Remark
2. Rated /	2-1. Practical temperature range			-30to +80	Humidity range: 85% RH.MAX.
	2-2. Preservation temperature range			-10to +40	Humidity range85% RH.MAX. 180
	2-3. Rated voltage and current(MAX.)			50V AC , 6A
	2-4. Appearance			No scratchessoilrust or discoloration on the surface.
3. Construction /	3-1. Outline And Dimension			Should match the attachment drawing.
3. Construction /	3-2. Part And Material			Should be consistent with the material list specifications.
4. Electrical efficiency /	4-1 Withstand Voltage		Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute	No dielectric breakd own shall occur.
	4-2 Insulation Resistance		Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	10000 M Min.
	4-3 Contact Resistance		Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA)	30 m MAX.
5. Mechanical Performance	5-1 Insertion and withdrawal forces		Rate of insertion/withdrawal: 2 mm/s Mating of complete connectors without the effect of any latching or retaining device	Insertion: 35 N max. Withdrawal: 2 N min.
5. Mechanical Performance	5-2 Terminal Strength		Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds.	There is no looseness, damage, etc., but the terminal deformation is acceptable.
6. Durability /	6 Life test		Under the condition of no load, rotate and then plug in , rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	Contact resistance: less than 50 m.	No obvious change in appearance, destruction.
7. Solderability /	7-1 Resistance to soldering heat		Temperature of solder: 2603. Dip time: 51 seconds.	After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base.
7. Solderability /	7-2 Solderability		Temperature of solder: 2453C. Time of dip: 30.5 seconds.	Coating of solder area should be more than 95%
8. Environment test /	8-1 Cold test		Place the housing for 96 hours at a low temperature of -30 3 C. Then ,place it under standard atmospheric conditions for 1 hour and test.	Contactresistance:50 mmax Insulation resistance500 M min Withstand voltage:AC 1000V	No obvious change in appearance
	8-2 Heat test		The housing should be stored at a temperature of 802for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test
	8-3 Humidity test		The housing should be stored at a temperature of 403with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test	Contact resistance:50mmax Insulation resistance500 M minWithstand voltage:AC 1000V	No obvious change in appearance
	8-4 Temperature Cycling		Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes.
	8-5 Salt spray test		Temperature: 35 2 Solution: 5 1% Spray time: 24hours	No obvious rust in the appearance.	Wash and dry it at room temperature after the experiment.
9. Test condition /			Standard: 15C~35C, 25%~85% RH, 86kPa~106kPa. Doubt condition: 201C, 63%~67% RH, 86kPa~106kPa.
10. Amendment /			Negotiated and agreed by the manufacturer and the customer.