electronic connector JINJIA XLR-16AP-2-N3B designed for stable performance in electronic applications

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR JACK SPECIFICATION

This specification applies to XLR jacks used in electronic products. These connectors are designed for reliable performance in various electronic applications.

Product Attributes

Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
Origin: China
Document Number: JJR-WI-47
Issue Date: 2008-09-10
Version: A1

Technical Specifications

Item	Property	Test Condition	Performance
2. Rated /	Practical temperature range	-30 to +80	-30 to +80
	Humidity range	85% RH.MAX.	85% RH.MAX.
	Rated voltage and current (MAX.)		50V AC , 6A
3. Construction /	Outline And Dimension	Should match the attachment drawing.	-
3. Construction /	Part And Material	Should be consistent with the material list specifications.	-
4. Electrical efficiency /	Withstand Voltage	Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute	No dielectric breakdown shall occur.
	Insulation Resistance	Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	10000 M Min.
	Contact Resistance	Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA)	30 m MAX.
5. Mechanical Performance	Insertion and withdrawal forces	Rate of insertion/withdrawal: 2 mm/s Mating of complete connectors without the effect of any latching or retaining device	Insertion: 35 N max. Withdrawal: 2 N min.
5. Mechanical Performance	Terminal Strength	Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds.	No looseness, damage, etc., but the terminal deformation is acceptable.
6. Durability /	Life test	Under the condition of no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	No obvious change in appearance, destruction. Contact resistance: less than 50 m.
7. Solderability /	Resistance to soldering heat	The jack terminal should be dipped in solder. Temperature of solder: 2603. Dip time: 51 seconds.	After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base.
7. Solderability /	Solderability	Temperature of solder: 2453C. Time of dip: 30.5 seconds.	Coating of solder area should be more than 95%.
8. Environment test /	Cold test	Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test.	No obvious change in appearance. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Heat test	The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	-
	Humidity test	The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	No obvious change in appearance. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
9. Test condition /	Standard Test Conditions	Temperature: 15C to 35C, Relative humidity: 25% to 85%, Atmospheric pressure: 86 kPa to 106 kPa. For critical judgment: 201C, 63% to 67% RH, 86 kPa to 106 kPa.	-
10. Amendment /	Specification Amendments	Requires negotiation and agreement between manufacturer and customer.	-