XLR jack connector JINJIA XLR-04-2 featuring rated electrical characteristics and resistance to corrosion
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
XLR Jack Specification
This specification applies to XLR jacks used in electronic products. It details the product's rated values, construction, electrical characteristics, mechanical performance, durability, solderability, environmental resistance, and testing conditions.
Product Attributes
- Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
- Origin: China
- Model Type: XLR JACK
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| Practical temperature range | -30to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10to +40 | ||
| Humidity range (Preservation) | 85% RH.MAX. | ||
| Storage Condition | Ambient air without acid, alkaline, or corrosive gases. Storage period not exceeding 180 days. | ||
| Rated voltage and current (MAX.) | 50V AC , 6A | ||
| Appearance | No scratches, soil, rust, or discoloration on the surface. | ||
| 3. Construction / | |||
| Outline And Dimension | Should match the attachment drawing. | ||
| Part And Material | Should be consistent with the material list specifications. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | Between two non-contact terminals | No dielectric breakdown |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | Between contactless terminals | 10000 M Min. |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | Matched terminals, tail end measurement | 30 m MAX. |
| 5. Mechanical Performance / | |||
| Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. | |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. There is no looseness, damage, etc., but terminal deformation is acceptable. | No looseness, damage. Deformation acceptable. | |
| 6. Durability / | |||
| Life test | Under no load conditions, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Matching plug, 1000 cycles | Appearance: No obvious change. Contact resistance: |
| 7. Solderability / | |||
| Resistance to soldering heat | The jack terminal should be dipped in solder: Temperature 2603, Dip time 51 seconds. After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | Solder dip | Plastic base: No deformation. Terminals: No detachment. |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. Coating of solder area should be more than 95%. | Solder dip | Solder area coverage: > 95%. |
| 8. Environment test / | |||
| Cold test | Place the housing for 96 hours at -30 3 C. Then, place under standard atmospheric conditions for 1 hour and test. | -30 3 C for 96h, then 1h standard conditions | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. |
| Heat test | The housing should be stored at 802 for 96 hours. Then, subject to standard atmospheric conditions for 1 hour and test. | 802 for 96h, then 1h standard conditions | |
| Humidity test | Store at 403 with 90% ~ 95% RH for 96 h. Then, subject to standard atmospheric conditions for 1 hour and test. | 403, 90%~95% RH for 96h, then 1h standard conditions | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. |
| Temperature Cycling | Place the Jack under specified conditions and then place in stand at room temperature for 30 minutes. | Specified conditions | |
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after the experiment. | 35 2, 5 1% salt solution, 24h | Appearance: No obvious rust. |
| 9. Test condition / | |||
| Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| Doubtful conditions | Test and measurement at 201C, relative humidity 63% to 67%, and air pressure 86 kPa to 106 kPa. | ||
| 10. Amendment / | |||
| Procedure | Amendments require negotiation and agreement between the manufacturer and the customer. | ||
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina