Professional audio electronic connector JINJIA XLR-25-1-N3GR XLR jack connectivity and durability

Name: Professional audio electronic connector JINJIA XLR-25-1-N3GR XLR jack connectivity and durability
Brand: Hefei Purple Horn E-Commerce Co., Ltd.

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR JACK SPECIFICATION

This specification applies to XLR jacks used in electronic products. The product is designed for professional audio and electronic applications, offering reliable connectivity.

Product Attributes

Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
Origin: China
Document Number: JJR-WI-47
Issue Date: 2008-09-10
Version: A1

Technical Specifications

Item	Property	Test Condition	Performance
2. Rated /
Practical temperature range	-30 to +80
Humidity range	85% RH.MAX.
Preservation temperature range	-10 to +40
Preservation humidity range	85% RH.MAX.
Storage Environment	Surrounding air free of acid, alkaline, or other corrosive gases. Storage period not exceeding 180 days.
Rated voltage and current (MAX.)	50V AC , 6A
Appearance	No scratches, soil, rust, or discoloration on the surface.
3. Construction /
Outline And Dimension	Should match the attachment drawing.
Part And Material	Should be consistent with the material list specifications.
4. Electrical efficiency /
Withstand Voltage	Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur.	Between two non-contact terminals	No dielectric breakdown
Insulation Resistance	Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	Between any contactless terminal and the other terminal	10000 M Min.
Contact Resistance	Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA).	Matched terminals, tail end measurement	30 m MAX.
5. Mechanical Performance /
Insertion and withdrawal forces	Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device.		Insertion: 35 N max. Withdrawal: 2 N min.
Terminal Strength	Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds.		No looseness, damage, etc. Terminal deformation is acceptable.
6. Durability /
Life test	Under no load conditions, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	Matching plug, 1000 cycles	Appearance: No obvious change. Contact resistance: less than 50 m.
7. Solderability /
Resistance to soldering heat	The jack terminal should be dipped in solder. Temperature of solder: 2603. Dip time: 51 seconds.		After test, plastic base should not be deformed and terminals should not fall off.
Solderability	Temperature of solder: 2453C. Time of dip: 30.5 seconds.		Coating of solder area should be more than 95%.
8. Environment test /
Cold test	Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test.		Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
Heat test	The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test.		(Performance not explicitly stated for Heat Test, but implied to be similar to Cold Test and Humidity Test based on context)
Humidity test	The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test.		Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
Temperature Cycling	Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes.	(Specific conditions not detailed in text)	(Performance not explicitly stated)
Salt spray test	Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after the experiment.		Appearance: No obvious rust.
9. Test condition /
Standard Conditions	Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa.
Doubtful Judgment Conditions	Test and measurement at 201C, relative humidity 63% to 67%, air pressure: 86 kPa to 106 kPa.
10. Amendment /
Procedure	Amendments require negotiation and agreement between the manufacturer and the customer.