electronic XLR jack connector JINJIA XLR-16A-1-N3GR rated 50V AC 6A current humidity range 85 percent RH max
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
XLR Jack Specification
This specification applies to XLR jacks used in electronic products. It details the electrical, mechanical, durability, and environmental performance of the XLR jack, ensuring its suitability for various applications.
Product Attributes
- Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
- Origin: China
- Model Type: XLR JACK
Technical Specifications
| Item | Property | Test Condition | Performance |
|---|---|---|---|
| 2. Rated / | |||
| Practical temperature range | -30 to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Preservation humidity range | 85% RH.MAX. | ||
| Storage environment | Ambient air without acid, alkaline or other corrosive gases. Storage period not exceed 180 days. | ||
| Rated voltage and current (MAX.) | 50V AC, 6A | ||
| Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 3. Construction / | |||
| Outline and Dimension | Should match the attachment drawing. | ||
| Part and Material | Should be consistent with the material list specifications. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | Between two non-contact terminals | No dielectric breakdown |
| Insulation Resistance | 10000 M Min. | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. |
| Contact Resistance | 30 m MAX. | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. |
| 5. Mechanical Performance | |||
| Insertion and withdrawal forces | Insertion: 35 N max. Withdrawal: 2 N min. | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. |
| Terminal Strength | No looseness, damage, etc., but terminal deformation is acceptable. | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage |
| 6. Durability / | |||
| Life test | Appearance: No obvious change, destruction. Contact resistance: less than 50 m. | Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Appearance: No obvious change. Contact resistance: |
| 7. Solderability / | |||
| Resistance to soldering heat | Plastic base should not be deformed and terminals should not fall off the plastic base. | Dip terminal in solder: Temperature: 2603. Dip time: 51 seconds. | No deformation, no detachment |
| Solderability | Coating of solder area should be more than 95% | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | >95% solder coverage |
| 8. Environment test / | |||
| Cold test | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | Place housing for 96 hours at -30 3 C. Then, place under standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. |
| Heat test | Store housing at 802 for 96 hours. Then subject to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | Store housing at 403 with 90% ~ 95% RH for 96 h. Then subject to standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. |
| Temperature Cycling | Place Jack under specified conditions, then place in stand at room temperature for 30 minutes. | ||
| Salt spray test | No obvious rust in appearance. | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after experiment. | No obvious rust |
| 9. Test condition / | |||
| Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. For judgment doubts: 201C, 63% to 67% RH, 86 kPa to 106 kPa. | ||
| 10. Amendment / | |||
| Procedure | Amendments require negotiation and agreement between manufacturer and customer. | ||
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina