Speaker socket connection XLR jack combo JINJIA XLR-11W-N3B ideal for electronic device applications

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR JACK (Combo) SPECIFICATION

This specification applies to XLR jack (Combo) which is used in electronic products. The connector is designed for speaker socket connections.

Product Attributes

Brand: Shenzhen jinjiarun Electronic Technology Co., Ltd
Origin: Shenzhen
Document Number: JJR-WI-46
Issue Date: 2008-09-10
Version: A1
Page: 1/6, 2/6, 3/6, 4/6, 5/6, 6/6

Technical Specifications

Item	Property	Test Condition	Performance
2. Rated /	Practical temperature range	-30to +80
	Humidity range	85% RH.MAX.
	Preservation temperature range	-10to +40	Humidity range85% RH.MAX. Around air free of acid, alkali or other corrosive gases. Storage period not exceed 180 Days.
	Rated voltage and current(MAX.)		50V AC , 3A(Type A) 7.5A(Type B)
4. Electrical efficiency /	Withstand Voltage	Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute	No dielectric breakdown shall occur.
4. Electrical efficiency /	Insulation Resistance	Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds.	10000 M Min.
	Contact Resistance	Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA)	30 m MAX.
5. Mechanical Performance /	Insertion and withdrawal forces	Rate of insertion/withdrawal: 2 mm/s Mating of complete connectors without the effect of any latching or retaining device	XLR: Insertion: 35 N max. Withdrawal: 2 N min. JACK: Insertion: 40 N max. Withdrawal: 5 N min.
	Terminal Strength	Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds.	No looseness, damage, etc., but terminal deformation is acceptable.
	Durability /	Life test: Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute.	No obvious change in appearance, destruction. Contact resistance: less than 50 m.
7. Solderability /	Resistance to soldering heat	The jack terminal should be dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds.	After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base.
7. Solderability /	Solderability	Temperature of solder: 2453C. Time of dip: 30.5 seconds.	Coating of solder area should be more than 95%
8. Environment test /	Cold test	Place the housing for 96 hours at -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test.	No obvious change in appearance. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Heat test	The housing should be stored at 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test.
	Humidity test	The housing should be stored at 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test.	No obvious change in appearance. Contact resistance: 50mmax. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
	Temperature Cycling	Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes.
	Salt spray test	Temperature: 35 2 Solution: 5 1% Spray time: 24 hours. Wash and dry at room temperature after the experiment.	No obvious rust in the appearance.
9. Test condition /	Unless otherwise specified, test and measurement temperature is between 15C and 35C, relative humidity is between 25% and 85%, and atmospheric pressure is between 86 kPa and 106 kPa. If doubts arise, test at 201C, 63% to 67% relative humidity, and 86 kPa to 106 kPa atmospheric pressure.
10. Amendment /	Amendments require negotiation and agreement between the manufacturer and the customer.
12. XLR JACK (Combo) TYPE /XLR	Type A, Type B