electrical JINJIA XLR-26A-10P XLR jack combo connector rated voltage 50V AC 3A and 7.5A for electronic
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
This specification applies to XLR jack (Combo) connectors used in electronic products. It details the electrical, mechanical, and environmental performance requirements for these connectors.
Product Attributes
- Brand: Jinjiarun
- Origin: Shenzhen, China
Technical Specifications
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| Practical temperature range | -30 to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Preservation humidity range | 85% RH.MAX. | ||
| Storage environment | Around air without acid, alkaline or other corrosive gases. Storage period not exceed 180 days. | ||
| Rated voltage and current (MAX.) | 50V AC, 3A (Type A) | ||
| Rated voltage and current (MAX.) | 50V AC, 7.5A (Type B) | ||
| Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | Between two non-contact terminals | No dielectric breakdown |
| Insulation Resistance | 10000 M Min. | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. |
| Contact Resistance | 30 m MAX. | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. |
| 5. Mechanical Performance / | |||
| Insertion and withdrawal forces | XLR: Insertion: 35 N max. Withdrawal: 2 N min. | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | |
| Insertion and withdrawal forces | JACK: Insertion: 40 N max. Withdrawal: 5 N min. | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | |
| Terminal Strength | No looseness, damage, etc., but terminal deformation is acceptable. | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc. |
| 6. Durability / | |||
| Life test | Appearance: No obvious change, destruction. Contact resistance: less than 50 m. | Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Contact resistance |
| 7. Solderability / | |||
| Resistance to soldering heat | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | The jack terminal should be dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds. | No deformation, no terminal detachment |
| Solderability | Coating of solder area should be more than 95% | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | >95% solder coverage |
| 8. Environment test / | |||
| Cold test | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | Place the housing for 96 hours at -30 3 C. Then, place under standard atmospheric conditions for 1 hour and test. | |
| Heat test | The housing should be stored at 802 for 96 hours. Then, subject to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | Stored at 403 with relative humidity of 90% ~ 95% for 96 h. Then, subject to standard atmospheric conditions for 1 hour and test. | |
| Salt spray test | No obvious rust in the appearance. | Temperature: 35 2. Solution: 5 1%. Spray time: 24hours. Wash and dry at room temperature after the experiment. | No obvious rust |
| 9. Test condition / | |||
| Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| Doubtful conditions | Test and measurement temperature: 201C, relative humidity: 63% to 67%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| 12. XLR JACK (Combo) TYPE /XLR | |||
| Type A | Rated current: 3A | ||
| Type B | Rated current: 7.5A | ||
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina