Durable Horizontal SMT Connector JUSHUO GH125-S12DCA-00 1.25mm Pitch Latch Type Electrical Component

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document details the specifications for the 1.25mm pitch horizontal SMT connector with latch, model GH125-S**DCA-00. It covers standard ratings, packaging, transportation, storage, component materials, appearance, electrical, environmental, and mechanical characteristics. This specification is applicable to the GH series products.

Product Attributes

Brand: (SHENZHEN JUSHUO ELECTRONIC CO.,LTD)
Origin: China
Certifications: ROHS

Technical Specifications

Item	Specifications	Test Method	Performance Requirements
Standard Rating
Rated Voltage	50V
Rated Current	1.0A AC/DC
Operating Temperature Range	-2585
Operating Humidity Range	Relative humidity is below 90%
Component Material
Part Name	Model	Material
Base	GH	LCP E130i
Pin	GH	Phosphor copper
Stator	GH	Phosphor copper
Electrical Characteristics
Contact Resistance		Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector Form a closed loop between.	20m Max
Insulation Resistance		Plug in the connector and apply 100V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute.	500M Min
Withstand Voltage		Plug in the connector and apply 500V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute.	No breakdown and flashover
Environmental Characteristics
Heating Test		Put the plug connector in the environment of +852 for 96H, take it out and put it in the normal environment for 1~2H before testing.	Appearance: no damage; Contact resistance: 60m Max
Cold Tolerance Test		The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested.	Appearance: no damage; Contact resistance: 60m Max
Moisture Resistance Test		Place the plug connector in an environment with a temperature of 402 and relative humidity of 90~96%. Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test.	Appearance: no damage; Insulation resistance: 60M min; Withstand voltage: 250V AC/minute MIN
Temperature Cycle		Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +853 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environment Check later.	Appearance: no abnormality; Contact resistance: 60m Max
Salt Spray Test		The test sample was suspended from the top of the test box, and the concentration of (51)% Sodium Chloride Solution was continuously sprayed with 24H. After testing, the surface precipitates were lightly washed with flowing steaming water, then the 1~2H was rechecked at normal temperature.	Appearance: no damage or corrosion (hardware should not expose the bottom metal of serious corrosion: use pre-plating The blanking surface is allowed to have a slight corrosion that does not affect its performance. Contact resistance: 60m Max
Weldability		Dip the welded part of the test sample into 2605 tin solution and hold 2.50.5 seconds.	Tin area above 95%
Soldering Resistance		Place the connector on the PCB, and then reflow the product through 2605 Or wave soldering for 51s.	1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. The electrical characteristics must meet the specifications.
Mechanical Properties
Pin Fixing Force		Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder.	Single pin 5N min
Terminal Retention in Plastic Parts		The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket.	Single terminal: 7N min
Mechanical Life		Under no power on state, plug and unplug 30 times at the speed of 10 times / min.	Contact resistance: 80m Max
Terminal Crimp Lead Line Strength		The terminals are pressed into wire at 253mm per minute The axial pullout rate of	26AWG wire: 17.8N; 28AWG wire: 8.9N; 30AWG wire: 4.4N; 32AWG wire: 2.2N
Insertion Pull Out Force		(1) Fit the hole seat and the terminal, and conduct the insertion and removal test on the same axis with the needle seat. Remove the lock of the hole seat (test speed: 20 5mm) minute during the test	(2) Performance requirements: Insertion force: 2N(Per pin); Pullout force: 0.3N(Per pin)