Wafer Patch Socket Connector 1.0mm Pitch JUSHUO AFC10-S04QCA-00 for FPC FFC Applications

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Specification

This specification covers the 1.0mm Pitch wafer patch socket connectors. It is designed for FPC/FFC applications and meets ROHS environmental requirements.

Product Attributes

Brand: JUSHUO ()
Origin: Shenzhen, China
Certifications: ROHS

Technical Specifications

Item	Specification	Requirement
2. Product Name and Part Number
Product Name	WAFER
Part Number	AFC10-S**QCA-00
3. Ratings
Rated Voltage (MAX)	50V
Rated Current (MAX)	0.5A [AC/DC (Virtual value) 50Hz]
Ambient Temperature Range	-45 +85	(Including terminal temperature rise)
4. Component Specification
Base Material	LCP E130i
Pin Material	Phosphor copper
Stator Material	Phosphor copper
6. Performance
6.1 Electrical Performance
Item	Test Condition	Requirement
Contact Resistance	Plug in the connector and test with a contact resistance meter. Measure between two terminals of the connector to form a closed loop.	20 m MAX
Insulation Resistance	Plug in the connector and apply 500V DC voltage between adjacent contacts and between contacts and enclosure for 1 minute.	500M MIN
Dielectric Strength	Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminals or ground.	No Breakdown
6.2 Mechanical Performance
Item	Test Condition	Requirement
Pin fixing force	Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder.	Single pin: 5N MIN
Terminal Retention in Plastic parts	The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket.	Single terminal: 5N MIN
6.3 Environmental Performance
Item	Test Condition	Requirement
Heat Resistance	Place the connector in an environment of +852 for 96H, then remove and test after 1-2H in normal environment.	Contact Resistance: 30 m MAX; Appearance: No Damage
Cold Resistance	Place the connector in an environment of -452 for 96H, then remove and test after 1-2H in normal environment.	Contact Resistance: 30 m MAX; Appearance: No Damage
Humidity	Place the connector in an environment of 452, relative humidity 90-96% for 96H. After testing, remove and test after 1-2H in normal environment.	Contact Resistance: 30 M MIN; Dielectric Strength: 500V AC/MIN; Appearance: No Damage
Temperature Cycling	Test samples are placed in high and low temperature test chambers and the temperature is adjusted according to the following steps: a) Maintain at -453 for 30 minutes; b) Maintain at normal temperature for 1H; c) Maintain at 853 for 30 minutes; d) Maintain at normal temperature for 1H; a to d is one cycle, a total of 5 cycles. After recovery in a normal environment for 2H, inspect.	Contact Resistance: 60 m MAX; Appearance: No Damage
Salt Spray Resistance	Test samples are suspended from the top of the test chamber; sprayed with 5 1% salt water at 452 for 48 hours; washed with normal temperature water after testing; then dried at room temperature.	Contact Resistance: 30 m MAX; Appearance: No Damage, Corrosion
Solder Ability	Immerse the sample's welding surface in a 2455 tin bath for 2.50.5 sec.	Tin Area: Above 95%
Soldering Resistance	Place the connector on a PCB board and immerse in a 2605 tin bath for 50.5 sec.	Tin Area: Above 95%; Appearance: No Damage, Deformation
7. Appearance and Size
Item	Specification	Requirement
Appearance	The surface of plastic parts shall be free of obvious scars, mottled, cracked, burr, flash, lack of material and deformation affecting the use; the surface of metal parts shall be smooth and clean, no rust, oxidation, peeling, blackening and obvious mechanical damage.
Size	Refer to engineering drawing