125mm pitch wafer patch socket connector JUSHUO GH125-S04CCA-00 for FPC and FFC connection solutions

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

SHENZHEN JUSHUO ELECTRONICS CO.,LTD - GH125-S**CCA-00 WAFER Patch Socket

The GH125-S**CCA-00 is a 1.25mm pitch wafer patch socket connector designed for FPC/FFC applications. It offers reliable electrical and mechanical performance, adhering to ROHS environmental requirements.

Product Attributes

Brand: JUSHUO
Origin: Shenzhen, China
Material: LCP (Base), Phosphor copper (Pin, Stator)
Certifications: ROHS

Technical Specifications

Item	Specification	Condition	Requirement
2. Product Name and Part Number
Product Name	WAFER
Part Number	GH125-S**CCA-00
3. Ratings
Rated Voltage (MAX)	50V
Rated Current (MAX)	1A [AC/DC (Virtual value) 50Hz]
Ambient temperature Range	-45 +85	(Including terminal temperature rise)
6. Performance
6.1 Electrical Performance
Contact Resistance	Plug in the connector and test with a contact resistance meter to measure both terminals of the connector form a closed loop between.		20 m MAX
Insulation Resistance	Plug in the connector and apply 500V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute.		500M MIN
Dielectric Strength	Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminals or ground.		No Breakdown
6.2 Mechanical Performance
Pin fixing force	Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder.	Single pin	5N MIN
Terminal Retention in Plastic parts	The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket.	Single terminal	5N MIN
6.3 Environmental Performance
Heat Resistance	Place the connector in an environment of +852 for 96H, take it out and test after 1-2H in normal environment.	852, 96 hour	Appearance: No Damage; Contact Resistance: 30 m MAX
Cold Resistance	Place the connector in an environment of -452 for 96H, take it out and test after 1-2H in normal environment.	-452, 96 hour	Appearance: No Damage; Contact Resistance: 30 m MAX
Humidity	Place the connector in an environment of 452, relative humidity 90~96% for 96H. After the test, take it out and test after 1~2H in normal environment.	Temperature: 452 Relative Humidity: 90-96% Duration: 96 Hours	Appearance: No Damage; Insulation Resistance: 30M MIN; Dielectric Strength: 500V AC/MIN
Temperature Cycling	Test samples are placed in a high and low temperature test chamber and adjusted according to the following steps: a) Maintain at -453 for 30 minutes; b) Maintain at normal temperature and humidity for 1H; c) Maintain at 853 for 30 minutes; d) Maintain at normal temperature and humidity for 1H; a to d is one cycle, a total of 5 cycles. Recover in normal environment for 2H before inspection.	a)-453 30minutes; b)Normal temp/humidity 1H; c)853 30minutes; d)Normal temp/humidity 1H, 5 cycles.	Appearance: No Damage; Contact Resistance: 60 m MAX
Salt Spray Resistance	Test samples are suspended from the top of the test chamber; 48 hours of exposure to a salt spray from a 5 1% solution at 452. After the test, rinse with water at room temperature and then dry at room temperature.	48 hours exposure to a salt spray from the 5 1% solution at 452.	Appearance: No Damage, Corrosion
Salt Spray Resistance	Test samples are suspended from the top of the test chamber; 484 hours of exposure to a salt spray from a 51% solution at 452. After the test, rinse with water at room temperature and then dry at room temperature.	484 hours exposure to a salt spray from the 51% solution at 452.	Appearance: No Damage; Contact Resistance: 30 m MAX
Solder Ability	Immerse the sample's soldering surface into a tin bath at 2455 for 2.50.5 sec.	Soldering Time: 2.50.5 sec. Soldering Temperature: 2455 0.2 mm from terminal tip.	Tin Area: Above 95%
Soldering Resistance	Place the connector on a PCB board and immerse it into a tin bath at 2605 for 50.5 sec.	Soldering Time: 50.5 sec. Soldering Temperature: 2605 0.2 mm from terminal tip.	Appearance: No Damage, Deformation; Tin Area: Above 95%
7. Appearance and Size
Appearance	The surface of plastic parts shall be free of obvious scars, mottled, cracked, burr, flash, lack of material and deformation affecting the use; the surface of metal parts shall be smooth and clean, no rust, oxidation, peeling, blackening and obvious mechanical damage.
Size	Refer to engineering drawing