1.25mm Pitch Horizontal Surface Mount Connector Latch JUSHUO GH125-S05DCA-00 Rated Voltage 50V Current 1.0A

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document is a product acknowledgment for the 1.25mm pitch horizontal surface mount connector with latch, model GH125-S**DCA-00. It details the product's specifications, performance characteristics, and testing procedures to ensure quality and compliance.

Product Attributes

Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
Origin: Shenzhen, China
Certifications: ROHS environmental protection requirements

Technical Specifications

Item	Specifications	Test Method	Performance Requirements
Standard Rating
Rated Voltage	50V
Rated Current	1.0A AC/DC
Operating Temperature Range	-2585
Operating Humidity Range	Relative humidity is below 90%
Environmental Protection
Compliance	Products in line with ROHS environmental protection requirements.
Packing
Method	Inner packing is joint and several, outer packing is carton. Product is sealed in the box, do not shake.
Transport
Conditions	Allowed by any means, avoid rain, snow, sunlight, collision, extrusion. Ambient temperature: -20 to +50.
Storage
Conditions	Ambient temperature: -20 to +50, relative humidity 90%. No acid, alkaline, or other corrosive gases in the surrounding air.
Part Name/Material
Base	GH LCP E130i
Pin	GH Phosphor copper
Stator	GH Phosphor copper
Appearance
Plastic Parts	Free of obvious scars, mottled, cracked, burr, flash, lack of material, and deformation affecting use.
Metal Parts	Smooth, clean, no rust, oxidation, peeling, blackening, or obvious mechanical damage.
Electrical Characteristics
Contact Resistance	20m Max	Plug in connector, test with contact resistance meter.
Insulation Resistance	500M Min	Plug in connector, apply 100V DC between adjacent contacts and between contacts and enclosure for 1 minute.
Withstand Voltage	No breakdown and flashover	Plug in connector, apply 500V AC between adjacent contacts and between contacts and enclosure for 1 minute.
Environmental Characteristics
Heating Test	Appearance: no damage. Contact Resistance: 60m Max	Plug connector in +852 for 96H, then in normal environment for 1-2H.
Cold Tolerance Test	Appearance: no damage. Contact Resistance: 60m Max	Plug connector in -252 for 96H, then in normal environment for 1-2H.
Moisture Resistance Test	Appearance: no damage. Insulation Resistance: 60M Min. Withstand Voltage: 250V AC/minute MIN.	Place plug connector in 402, 90-96% RH for 96H, then in normal environment for 1-2H.
Temperature Cycle	Appearance: no abnormality. Contact Resistance: 60m Max	5 cycles of -253 (30min) -> Room Temp (1H) -> +853 (30min) -> Room Temp (1H). Recover 2H.
Salt Spray Test	Appearance: no damage or corrosion. Contact Resistance: 60m Max	Continuous spray with 51% NaCl solution for 24H. Wash with distilled water, recover 1-2H.
Weldability	Tin area above 95%	Dip welded part in 2605 tin solution for 2.50.5 seconds.
Soldering Resistance	1. Plastic parts: no obvious deformation, damage, blistering. 2. Electrical characteristics meet specifications.	Place connector on PCB, reflow or wave solder at 2605 for 51S.
Mechanical Properties
Pin Fixing Force	Single pin 5N min	Fix pin holder, apply force on pin front end at 253mm/min rate until pin withdraws.
Terminal Retention in Plastic Parts	Single terminal: 7N min	Match terminal with hole seat, pull terminal out at 253mm/min along wire direction.
Mechanical Life	Contact Resistance: 80m Max	Plug and unplug 30 times at 10 times/min without power.
Terminal Crimp Wire Strength	26AWG wire: 17.8N. 28AWG wire: 8.9N. 30AWG wire: 4.4N. 32AWG wire: 2.2N.	Axial pullout force at 253mm/min rate.
Insertion/Pullout Force	Insertion force: 2N(Per pin). Pullout force: 0.3N(Per pin).	Fit hole seat and terminal, insert/remove on same axis. Remove lock of hole seat. Test speed: 205mm/min.