Compact 1.0mm Pitch Vertical SMT Connector JUSHUO AFC10-S02PCA-00 with ROHS Environmental Compliance

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This product acknowledgment document details the 1.0mm pitch vertical SMT connector, model AFC10-S**PCA-00. It outlines the product's specifications, electrical and environmental characteristics, and mechanical properties, intended for customer confirmation.

Product Attributes

Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
Product Name: 1.0mm
Product Model: AFC10-S**PCA-00
Version: 1 1 version
Material: Base: LCP E130i, Reed: Phosphor copper, Stator: Phosphor copper
Environmental Compliance: ROHS

Technical Specifications

Item	Specifications	Test Method	Performance Requirement
Standard Rating
Rated Voltage	50V
Rated Current	0.5A AC/DC
Operating Temperature Range	-25+105
Operating Humidity Range	Relative humidity is below 90%
Electrical Characteristics
Contact Resistance		Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector Form a closed loop between.	20m Max
Insulation Resistance		Plug in the connector and apply 500V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute.	100M Min
Withstand Voltage		Plug in the connector and apply 500V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute.	No breakdown and flashover
Environmental Characteristics
Heating Test		Put the plug connector in the environment of +1052 for 96H, take it out and put it in the normal environment for 1~2H before testing.	Appearance: appearance without damage; Contact resistance: 30m Max
Cold Tolerance Test		The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested.	Appearance: appearance without damage; Contact resistance: 30m Max
Moisture Resistance Test		Place the plug connector in an environment with a temperature of 402 and relative humidity of 90 96%.Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test.	Appearance: appearance without damage; Insulation resistance: 50M min; Withstand voltage: 200VAC/min te MIN
Temperature Cycle		Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +1053 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environment Check later.	Appearance: no abnormalities; Contact resistance: 30m Max
Salt Spray Test		Suspend the test sample from the top of the test chamber with a concentration of (5 1)% of Sodium Chloride Solution, continuous spray 24H, after test, with flowing steaming water gently. Wash away the precipitates on the surface, recover for 1 ~ 2H under normal temperature, and then check and measure.	Appearance: no damage or corrosion (Hardware should have no exposed bottom metal Severe corrosion: use pre-plating well The profile, the blanking surface is allowed to have Slight corrosion that does not affect its performance.); Contact resistance: 30m Max
Weldability		Dip the welded part of the test sample into 2355 tin solution and hold 2.50.5 seconds.	Tin area above 95%
Soldering Resistance		Place the connector on the PCB, and then reflow the product through 260 5 Or wave soldering for 51s.	1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. The electrical characteristics must meet the specifications.
Mechanical Properties
Pin Fixing Force		Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder.	Single pin 7N min
Terminal Retention in Plastic Parts		The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket.	Single terminal: 5N min
Mechanical Life		Under no power on state, plug and unplug 50 times at the speed of 10 times / min.	Contact resistance: 30m Max
Insert Force/Draw Force	(1) the hole seat and the terminal should be well matched, and the pin seat should be inserted on the same axis for the test. The hole seat should be locked during the test Remove (test speed: 205mm/minute (2) Performance requirements: PIN Position Insert (N) Pull out (N) PIN Position Insert (N) Pull out (N) 1 3.00 0.50 9 29.00 5.50 2 8.00 2.00 10 32.00 6.00 3 11.00 2.50 11 35.00 6.50 4 14.00 3.00 12 38.00 7.00 5 17.00 3.50 13 41.00 7.50 6 20.00 4.00 14 44.00 8.00 7 23.00 4.50 15 47.00 8.50 8 26.00 5.00 16 50.00 9.00