2.5mm Vertical Surface Mount Connector JUSHUO AFC25-S03CCA-00 with Low Electrical Contact Resistance

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This product acknowledgment document details the specifications for the 2.5mm vertical surface mount connector, model AFC25-S**CCA-00. It covers standard ratings, packaging, transportation, storage, part details, electrical, environmental, and mechanical characteristics.

Product Attributes

Brand: SHENZHEN JUSHUO ELECTRONIC CO.,LTD
Origin: China (implied by company address)
Certifications: ROHS environmental protection requirements

Technical Specifications

Item	Specifications	Requirements	Test Method
Standard Rating
Rated Voltage	250V
Rated Current	3.0A AC/DC
Operating Temperature Range	-25+105
Operating Humidity Range	Relative humidity is below 90%
Part Name/Specification/Material
Base	2.5 LCP E130i
Pin	2.5 Brass
Stator	2.5 Brass
Electrical Characteristics
Contact Resistance	20m Max		Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector Form a closed loop between.
Insulation Resistance	1000M Min	1000V DC for 1 minute between adjacent contacts and between contacts and enclosure.	Plug in the connector and apply 1000V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute.
Withstand Voltage	No breakdown and flashover	1000V AC for 1 minute between adjacent contacts and between contacts and enclosure.	Plug in the connector and apply 1000V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute.
Environmental Characteristics
Heating Test	Appearance: no damage. Contact resistance: 30m Max	+1052 for 96H, then 1~2H in normal environment.	Put the plug connector in the environment of +1052 for 96H, take it out and put it in the normal environment for 1~2H before testing.
Cold Tolerance Test	Appearance: no damage. Contact resistance: 30m Max	-252 for 96H, then 1~2H in normal environment.	The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested.
Moisture Resistance Test	Appearance: no damage. Insulation resistance: 500M Min. Withstand voltage: 800V AC/minute MIN	402, 90~96% RH for 96H, then 1~2H in normal environment.	Place the plug connector in an environment with a temperature of 402 and relative humidity of 90~96%.Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test.
Temperature Cycle	Appearance: no abnormalities. Contact resistance: 30m Max	5 cycles of: -253 for 30 min, room temp for 1H, +1053 for 30 min, room temp for 1H. Recover 2H.	Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +1053 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environmentCheck later.
Salt Spray Test	Appearance: no damage or corrosion (hardware should not expose the bottom metal of serious corrosion; use pre-plating, blanking surface is allowed to have slight corrosion that does not affect its performance). Contact resistance: 30m Max	Continuous spray for 24H with 51% NaCl solution, then wash with distilled water, recover 1~2H.	The test sample was suspended from the top of the test box, and the concentration of (51)% Sodium Chloride Solution was continuously sprayed with 24H. After testing, the surface precipitates were lightly washed with flowing steaming water, then the 1~2H was rechecked at normal temperature.
Weldability	Tin area above 95%	Dip the welded part into 2455 tin solution for 2.50.5 seconds.	Dip the welded part of the test sample into 2455 tin solution and hold 2.50.5 seconds.
Soldering Resistance	1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. Electrical characteristics must meet the specifications.	Reflow soldering or wave soldering at 2605 for 51S.	Place the connector on the PCB, and then reflow the product through 260 5 Or wave soldering for 5 1s.
Mechanical Properties
Pin Fixing Force	Single pin 12N Min		Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder.
Terminal Retention in Plastic Parts	Single terminal: 15N Min		The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket.
Mechanical Life	Contact resistance: 30m Max	Plug and unplug 50 times at the speed of 10 times / min under no power on state.	Under no power on state, plug and unplug 50 times at the speed of 10 times / min.
Insertion/Extraction Force	See table below	Test speed: 205mm/minute. Remove the lock of the hole seat.	(1) Fit the hole seat and the terminal, and conduct the insertion and removal test on the same axis with the needle seat. Remove the lock of the hole seat (test speed: 20 5mm) minute during the test
	Position	Insertion (N)	Pull out (N)
	1	16.00	2.00
	2	20.00	10.00
	3	24.00	12.00
	4	28.00	14.00
	5	32.00	16.00
	6	36.00	18.00
	7	40.00	20.00
	8	44.00	22.00
	9	48.00	24.00
	10	52.00	26.00
	11	56.00	28.00
	12	60.00	30.00
	13	64.00	32.00
	14	68.00	34.00
	15	72.00	36.00
	16	76.00	38.00