Durable SHOU HAN AF 10.0 QT-ZB6.8 rated DC 30V 1.5A connector with mechanical electrical specifications

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification document details the technical parameters for the QT-ZB6.8 product from Shenzhen Shouhan Technology Co., Ltd. It is designed for applications requiring a DC 30V 1.5A rating within a practical temperature range of -25C to 85C. The document outlines mechanical, electrical, and durability performance standards.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: Shenzhen, China

Technical Specifications

Item	Test Conditions	Performance	Specification
MECHANICAL
CONNECTION FORCE	Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times.		3.75kgf
DISCONNECTION FORCE	Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times.		1.02kgf
TERMINAL STRENGTH	A static load of 0.1N/m(1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical, and mechanical characteristics shall be satisfied.
ELECTRICAL
CONTACT RESISTANCE	Measured at small current (100mA or less) 1000Hz		30m
INSULATION RESISTANCE	Apply a voltage of 100V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted		1000M
DIELECTRIC STRENGTH	AC 500V rms(50~60Hz) for 1 min Trip Current:0.5mA (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted	Without damage to parts arcing or breakdown etc.
DURABILITY
SOLDERABILITY TEST	The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds.	(1) Solder wetting time shall be 3 sec or less (2) The area of soldering should be over 75%
RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING)	Preheat: Temperature on the copper foil surface should reach 180. 120s after the P.C.B entered into the soldering equipment.	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING)	Tallest Temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 with in 20 seconds.
RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON METHOD)	Bit temperature 3305 Application time of soldering iron 30.5 sec. However excessive pressure shall not be applied to the terminal.	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON METHOD)
HUMIDITY TEST	The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures.
HEAT TEST	The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery measurement.	There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied.
COLD TEST	The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which.	There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied.
LIFE TEST	Without Load: Connection and disconnection shall be made with the mating plugs and jacks for 5,000 cycles at a speed of 10 to 25 cycles/min.		5000 Cycles
	Load: At rating condition (non-inductive load) Connection and disconnection shall be made 5,000 cycles at a speed 10 to 20 cycles / min.
	(1) Contact Resistance shall be 0.1 (2) Disconnection Force shall be 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
TEMPERATURE CYCLING TEST	The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes.	There shall be no deformation or cracks in molded part. Insertion & Extraction Force: 3 to 20N Contact Resistance: Max.30m Insulation Resistance: Min.100 M Dielectric Withstanding Voltage: 100VAC/min (Between Terminals)
TEMPERATURE CYCLING TEST	Temp(): 70 (8 hours) to -20 (0.5 hours) per cycle.
COLD & HEAT SHOCK TEST	The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes.	There shall be no deformation or cracks in molded part. Insertion & Extraction Force: 3 to 25N Contact Resistance: Max.30m Insulation Resistance: Min.100 M Dielectric Withstanding Voltage: 500VAC/min (Between Terminals)
COLD & HEAT SHOCK TEST	Temp(): 70 (1 hour) to -20 (1 hour) per cycle.