SHOU HAN TYPE C 6P CC connector featuring Au Ni plated stainless steel terminals and plastic housing
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
High-temperature plastic TYPE-C 6P CC connector with Au/Ni plated or NI plated stainless steel terminals. Designed for reliable performance in demanding environments, featuring high durability and resistance to various environmental conditions. Suitable for applications requiring robust and long-lasting connectivity.
Product Attributes
- Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
- Origin: (Shenzhen)
- Material: High Temperature Plastic, Stainless Steel
- Finish: Au/Ni Plated, NI Plated
- Certifications: None explicitly mentioned
Technical Specifications
| Item | Test Conditions | Performance | Specification |
| MECHANICAL | |||
| 1. Insertion Force | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 5~20N | |
| 2. Unmating Force | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 8~20N | |
| 3. Terminal Strength | A static load of 0.1N/m(1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical, and mechanical characteristics shall be satisfied. | ||
| ELECTRICAL | |||
| 3.1 Contact Resistance | Measured at small current (100mA or less) 1000Hz | 40m MAX | |
| 3.2 Insulation Resistance | Apply a voltage of 100V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted | 100M MIN | |
| 3.3 Dielectric Strength | AC 100V rms(50~60Hz) for 1 min. Trip current:0.5mA. (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted | Without damage to parts arcing or breakdown etc. | |
| DURABILITY | |||
| 4.1 Solderability Test | The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds. | (1) Solder wetting time shall be 3 sec or less. (2) The area of soldering should be over 75%. | |
| 4.2 Resistance to Soldering Heat Test (Reflow Soldering) | Preheat: Temperature on the copper foil surface should reach 180. 120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds. | Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | |
| 4.2 Resistance to Soldering Heat Test (Soldering Iron Method) | Bit temperature 3305 Application time of soldering iron 30.5 sec. However excessive pressure shall not be applied to the terminal. | Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | |
| 4.3 Humidity Test | The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | |
| 4.4 Heat Test | The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery measurement. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | |
| 4.5 Cold Test | The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | |
| 4.6 Life Test (Without Load) | Connection and disconnection shall be made with the mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min. | ||
| 4.6 Life Test (With Load) | At rating condition (non-inductive load). Connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min. | (1) Contact resistance shall be 0.1. (2) Disconnection force shall be 0.8 to 2.0N. (3) Mechanical and electrical characteristics shall be satisfied. | |
| 4.7 Temperature Cycling Test | The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned to room ambient condition for 30 minutes. | Product cannot deform or crack. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 100VAC/min (between terminals). | |
| 4.8 Cold & Heat Shock Test | The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned to room ambient condition for 30 minutes. | Product cannot deform or crack. Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 500VAC/min (between terminals). | |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina