USB connector SHOU HAN 11.0 180°CB1.9 with precise contact resistance and strong disconnection force

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document outlines the specifications for a USB connector from Shenzhen Shouhan Technology Co., Ltd. It details the product's technical performance, including mechanical, electrical, and durability characteristics, designed for reliable operation within a specified temperature and atmospheric range.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: China
Contact: Tel: 0755-27597601, Fax: 0755-27597491

Technical Specifications

Item		Test Conditions		Performance
1	Connection Force	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES	PLUG GAUGE 3	MAX	3.57Kgf
2	Disconnection Force	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES	PLUG GAUGE 3	MIN	1.02Kgf
3.1	Contact Resistance	MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz	100 m A	MAX	30m
3.2	Insulation Resistance	APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	100V DC 1 1 2 3	MIN	1000M
3.3	Dielectric Strength	AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODYAND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3)	WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC
4.1	Solder- ability Test	THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS	1mm ,2505,5 0.5	(1) SOLDER WETTING TIME SHALL BE 3 SEC OR LESS (2) THE AREA OF SOLDERING SHOULD BE OVER 75%	(1) 3 (2) 75%
4.2	Resistance to Soldering Heat Test (Reflow)	REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180 .120 S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605 WITH IN 20 SECONDS.	:180,120s :260520	WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.2	Resistance to Soldering Heat Test (Soldering Iron)	SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL	3305 30.5	WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.3	Humidity Test	THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES	40290~96% Hr 96 1
4.4	Heat Test	THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM	70296 1	APPEARANCE, MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.5	Cold Test	THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH	-25396 1	APPEARANCE, MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.6	Life Test (Without Load)	CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN	Plug()1 10-255000	(1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	(1) 0.1 (2) 0.8~2.0N (3) :,
4.6	Life Test (Load)	CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN AT RATING CONDITION NON-INDUCTIVE LOAD	()1 10-20 5000	(1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	(1) 0.1 (2) 0.8~2.0N (3) :,
4.7	Temperature Cycling Test	THE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS)	3N 20N 30m 100 M 100VAC
4.8	Cold & Heat Shock Test	THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS)	3N 25N 30m 100 M 500VAC