SHOU HAN TYPE-C 16PIN 2MD073 connector with DC 5V 3A rating and temperature range minus 25 to 85 degrees
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
This document outlines the specifications for the TYPE-C 16PIN 2MD(073) connector from Shenzhen Shouhan Technology Co., Ltd. It details the product's ratings, operating temperature range, and performance under standard atmospheric conditions. The specification covers mechanical, electrical, and durability tests to ensure product reliability and performance.
Product Attributes
- Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
- Origin: (Shenzhen)
- Product Name: TYPE-C 16PIN 2MD(073)
- Contact Person (Drawn): (Li Chunfeng)
- Contact Person (Check): (Zhong Huahua)
- Contact Person (Approved): (Luo Xiaojin)
- Tel: 0755-27597601
- Fax: 0755-27597491
Technical Specifications
| Item | Project | Test Conditions | Performance (Specification) |
|---|---|---|---|
| RATING | |||
| DC 5V 3A | PRACTICAL TEMPERATURE RANGE | -25~85C | |
| STANDARD ATMOSPHERIC CONDITIONS | |||
| (1) Temperature | 5 TO 35 | ||
| (2) Humidity | 45% TO 85% | ||
| (3) Pressure | 86Kpa TO 106Kpa | ||
| MECHANICAL | |||
| 1 | CONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | 0.5-2.0Kgf |
| 2 | DISCONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | 0.8~2.0Kgf |
| 3 | TERMINAL STRENGTH | A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION. THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL, AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED. | N/A |
| ELECTRICAL | |||
| 3.1 | CONTACT RESISTANCE | MEASURED AT SMALL CURRENT (100mA OR LESS) 1000Hz | 40m |
| 3.2 | INSULATION RESISTANCE | APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | 100M |
| 3.3 | DIELECTRIC STRENGTH | AC 100V rms(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC |
| DURABILITY | |||
| 4.1 | SOLDERABILITY TEST | THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS. (1) SOLDER WETTING TIME SHALL BE 3 SEC OR LESS (2) THE AREA OF SOLDERING SHOULD BE OVER 75% | N/A |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING) | PREHEAT: 180, 120s. TALLEST TEMPERATURE: 2605 WITHIN 20 SECONDS. | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON METHOD) | BIT TEMPERATURE 3305 APPLICATION TIME 30.5 SEC. HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL. | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. |
| 4.3 | HUMIDITY TEST | STORED AT 402 AND 90%TO 96% RH FOR 96 Hr, THEN MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr. | N/A |
| 4.4 | HEAT TEST | STORED AT 702 FOR 96 HOURS, THEN SUBJECTED TO CONTROLLED RECOVERY FOR 1 HOUR. | APPEARANCE NO DAMAGE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. |
| 4.5 | COLD TEST | STORED AT -253 FOR 96 HOURS, THEN SUBJECTED TO CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR. | APPEARANCE NO DAMAGE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. |
| 4.6 | LIFE TEST (WITHOUT LOAD) | CONNECTION AND DISCONNECTION SHALL BE MADE WITH MATING PLUGS AND JACKS FOR 10000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN. | N/A |
| 4.6 | LIFE TEST (LOAD) | LOAD: AT RATING CONDITION (NON-INDUCTIVE LOAD). CONNECTION AND DISCONNECTION SHALL BE MADE 10000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN. (1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. | (1) 0.1 (2) 0.8 TO 2.0Kgf (3) SATISFIED |
| 4.7 | TEMPERATURE CYCLING TEST | SUBJECTED TO 5 CYCLES OF SPECIFIED CONDITIONS, THEN RETURNED TO ROOM AMBIENT FOR 30 MINUTES. | NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 20N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN (BETWEEN TERMINALS). |
| 4.8 | COLD & HEAT SHOCK TEST | SUBJECTED TO 5 CYCLES OF SPECIFIED CONDITIONS, THEN RETURNED TO ROOM AMBIENT FOR 30 MINUTES. | NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 25N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN (BETWEEN TERMINALS). |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina