High Durability SHOU HAN TYPE-C 16PFS LCH7.45 IPX8 Connector with IPX8 Protection and Connection Force

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document outlines the specifications for the TYPE-C 16PFS LCH7.45 IPX8 connector from Shenzhen Shouhan Technology Co., Ltd. It details the product's electrical, mechanical, and durability characteristics, designed for operation within a temperature range of -30~80C.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: (Shenzhen)
Model: TYPE-C 16PFS LCH7.45 IPX8
IP Rating: IPX8
Material Code: 3
Approval Signatures: , ,
Date: 2021.10.27

Technical Specifications

Item	Test Conditions	Performance	Specification
RATING
			DC20V
PRACTICAL TEMPERATURE RANGE
			-30~80C
STANDARD ATMOSPHEIC CONDITIONS
	(1) Temperature		5C TO 35
	(2) Humidity		45% TO 85%
	(3) Pressure		86Kpa TO 106Kpa
MECHANICAL
CONNECTION FORCE	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES.		0.5-2.0Kgf
DISCONNECTION FORCE	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES.		0.8-2.0Kgf
TERMINAL STRENGTH	A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION. THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY. ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED.
ELECTRICAL
CONTACT RESISTANCE	MEASURED AT SMALL CURRENT (100m A OR LESS) 1000Hz		40m MAX
INSULATION RESISTANCE	APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED		100M MIN
DIELECTRIC STRENGTH	AC 100V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC
DURABILITY
SOLDERABILITY TEST	THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS	(1) SOLDER WETTING TIME SHALL BE 3 SEC OR LESS (2) THE AREA OF SOLDERING SHOULD BE OVER 75%
RESISTANCE TO SOLDERING HEAT TEST	REFLOW SOLDERING CONDITIONS: PREHEAT: 180.120s. TALLEST TEMPERATURE: 2605 WITHIN 20 SECONDS.	WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
RESISTANCE TO SOLDERING HEAT TEST	SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON 30.5 SEC. HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL.	WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
HUMIDITY TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr, THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr.
HEAT TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF 702 FOR 96 HOURS, AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY.	THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
COLD TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF -253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR.	THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
LIFE TEST	WITHOUT LOAD: CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 10000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN.
LIFE TEST	LOAD: AT RATING CONDITION (NON-INDUCTIVE LOAD). CONNECTION AND DISCONNECTION SHALL BE MADE 10000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN.	(1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
TEMPERATURE CYCLING TEST	THE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS: 70 FOR 0.5 HOURS, 40 FOR 0.5 HOURS, 0 FOR 0.5 HOURS, -40 FOR 8 HOURS. THEN RETURNED TO ROOM AMBIENT FOR 30 MINUTES.	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 20N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN (BETWEEN TERMINALS).
COLD&HEAT SHOCK TEST	THE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS: 70 FOR 1 HOUR, -20 FOR 1 HOUR. THEN RETURNED TO ROOM AMBIENT FOR 30 MINUTES.	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 25N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN (BETWEEN TERMINALS).