Durable SHOU HAN TYPE-C 6P LCH10.0 connector designed for stable electrical and mechanical performance

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document outlines the specifications for the TYPE-C 6P LCH10.0 connector from SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD. It details the product's electrical, mechanical, and durability characteristics, designed for reliable performance under specified conditions.

Product Attributes

Brand: SHOUHAN TECHNOLOGY
Origin: Shenzhen, China
Model: TYPE-C 6P LCH10.0
Part Number: LCH10.0

Technical Specifications

Item	Test Conditions	Performance	Specification
RATING
Power			5 V 3 A
PRACTICAL TEMPERATURE RANGE
Operating Temperature			-30~80C
STANDARD ATMOSPHERIC CONDITIONS
Temperature	For measurements and tests		5C to 35
Humidity	For measurements and tests		45% to 85%
Pressure	For measurements and tests		86Kpa to 106Kpa
MECHANICAL
CONNECTION FORCE	After connecting and disconnecting using standard plug gauge 3 times		5-20N
DISCONNECTION FORCE	After connecting and disconnecting using standard plug gauge 3 times		8-20N
TERMINAL STRENGTH	A static load of 0.1N/m(1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. No damage such as cracks, looseness or play. Electrical and mechanical characteristics shall be satisfied.
ELECTRICAL
CONTACT RESISTANCE	Measured at small current (100mA or less)		40m MAX
INSULATION RESISTANCE	Apply a voltage of 100V DC for 1 min to following portions: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted		100M MIN
DIELECTRIC STRENGTH	AC 100V rms(50~60Hz) for 1 min. Trip current: 0.5mA. (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted	Without damage to parts, arcing or breakdown etc.
DURABILITY
SOLDERABILITY TEST	The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds. (1) Solder wetting time shall be 3 seconds or less (2) The area of soldering should be over 75%
RESISTANCE TO SOLDERING HEAT TEST (Reflow Soldering)	Preheat: Temperature on the copper foil surface should reach 180. After 120s, PCB enters soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds.	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
RESISTANCE TO SOLDERING HEAT TEST (Soldering Iron Method)	Bit temperature 3305. Application time of soldering iron 30.5 sec. However, excessive pressure shall not be applied to the terminal.	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
HUMIDITY TEST	The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then maintained at standard atmospheric condition for 1 Hr.
HEAT TEST	The jack shall be stored at a temperature of 702 for 96 Hours, then subjected to controlled recovery for 1 Hr.	No damage on appearance. Mechanical and electrical characteristics shall be satisfied.
COLD TEST	The jack shall be stored at a temperature of -253 for 96 Hours, then subjected to controlled recovery for 1 Hr.	No damage on appearance. Mechanical and electrical characteristics shall be satisfied.
LIFE TEST (Without Load)	Connection and disconnection shall be made with mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min.
LIFE TEST (With Load)	At rating condition (non-inductive load). Connection and disconnection shall be made for 5000 cycles at a speed of 10 to 20 cycles/min. (1) Contact resistance shall be 0.1 (2) Disconnection force shall be 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
TEMPERATURE CYCLING TEST	Subjected to 5 cycles of specified conditions, then returned to room ambient for 30 minutes.	No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 100VAC/min (between terminals).
COLD & HEAT SHOCK TEST	Subjected to 5 cycles of specified conditions, then returned to room ambient for 30 minutes.	No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 500VAC/min (between terminals).