Connector SHOU HAN TYPE-C 16PLC-H10.0 engineered for long-term mechanical and electrical durability

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document outlines the specifications for the TYPE-C 16PLC-H10.0 connector from Shenzhen Shouhan Technology Co., Ltd. It details the product's mechanical, electrical, and durability characteristics, along with testing conditions and performance requirements.

Product Attributes

Brand: SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD
Origin: Shenzhen, China
Model: TYPE-C 16PLC-H10.0
Part Number: 16PLC-H10.0
Material Code: PRACTICAL

Technical Specifications

Item		Test Conditions		Performance
Mechanical	Connection Force	Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times.	PLUG GAUGE 3	0.5-2.0Kgf
Mechanical	Disconnecti on Force	Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times.	PLUG GAUGE 3	0.8-2.0Kgf
	Terminal Strength	A static load of 0.1N/m(1kgf/cm)shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical, and mechanical characteristics shall be satisfied.	1 0.1N/m(1kgf/cm).
Electrical	Contact Resistance	Measured at small current (100mA or less) 1000Hz	100 m A	40m MAX
	Insulation Resistance	Apply a voltage of 100V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted	100V DC 1 1 2 3	100M MIN
	Dielectric Strength	AC 100V ims(50~60Hz)for 1 min Trip Current:0.5mA (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted	AC 100V 50Hz/min 1 0.5mA, : (1) (2) (3)	Without damage to parts arcing or breakdown etc
Durability	Solder- Ability Test	The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds. (1) Solder wetting time shall be 3 sec or less (2) The area of soldering should be over 75%	1mm ,2505,5 0.5 13 275%
	Resistance to Soldering Heat Test (Reflow Soldering)	Preheat: Temperature on the copper foil surface should reach 180.120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 with in 20 seconds.	:180,120s :260520	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
	Resistance to Soldering Heat Test (Reflow Soldering)	Resistance to Soldering Heat Test (Soldering Iron Method)	Bit temperature 3305 Application time of soldering iron 30.5 sec However excessive pressure shall not be applied to the terminal.	3305 30.5	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
	Humidity Test	The jack shall be stored at a temperature of 402 and a humidity of 90%to 96% for 96 Hr,then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures.	402 90~96% Hr 96 1
	Heat Test	The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery measurement.	70296 1	There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied.
	Cold Test	The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which.	-25396 1	There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied.
	Life Test (Without Load)	Connection and disconnection shall be made with the mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min.	Plug()1 10-255000	(1) Contact resistance shall be 0.1 (2) Disconnection force shall be 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
	Life Test (Load)	At rating condition (non-inductive load) connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min.	()1 10-205000	(1) Contact resistance shall be 0.1 (2) Disconnection force shall be 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
	Temperature Cycling Test	The jack shall be subjected to 5 cycles of the following conditions, and then shall return to room ambient condition for 30 minutes.	5 30	Product cannot deform or crack. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max.30m. Insulation Resistance: Min.100 M. Dielectric Withstanding Voltage: 100VAC/min (between terminals).
	Cold & Heat Shock Test	The jack shall be subjected to 5 cycles of the following conditions, and then shall return to room ambient condition for 30 minutes.	5 30	Product cannot deform or crack. Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max.30m. Insulation Resistance: Min.100 M. Dielectric Withstanding Voltage: 500VAC/min (between terminals).