Mechanical and electrical USB AF connector SHOU HAN AF 10.0 HC6.3 two pin plug in 10 millimeter pitch
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
USB-AF connector, 10.0mm pitch, two-pin plug-in, straight edge, 6.3mm series. Rated for DC 30V 1.5A and an operating temperature range of -25C to 85C. Designed for reliable mechanical and electrical performance, meeting stringent industry standards for durability, heat resistance, cold resistance, and electrical characteristics.
Product Attributes
- Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO., LTD)
- Origin: China
Technical Specifications
| ITEM | TEST CONDITIONS | PERFORMANCE | SPECIFICATION |
| RATING | |||
| RATING | DC 30V 1.5A | ||
| PRACTICAL TEMPERATURE RANGE | -25~85C | ||
| MECHANICAL | |||
| 1 | CONNECTION FORCE (After 3 cycles) | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | 3.75Kgf |
| 2 | DISCONNECTION FORCE (After 3 cycles) | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | 1.02Kgf |
| 3 | TERMINAL STRENGTH | A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION. THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED | |
| ELECTRICAL | |||
| 3.1 | CONTACT RESISTANCE (At small current 100mA, 1000Hz) | MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz | 30m |
| 3.2 | INSULATION RESISTANCE (Apply 100V DC for 1 min) | APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | 1000M |
| 3.3 | DIELECTRIC STRENGTH (AC 500Vrms for 1 min, Trip Current: 0.5mA) | INPUT AC 500V (50Hz)/min VOLTAGE FOR 1 MIN. TEST ACCORDING TO THE FOLLOWING CONTACT METHODS: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC |
| DURABILITY | |||
| 4.1 | SOLDERABILITY TEST | THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS | (1) SOLDER WETTING TIME SHALL BE 3 SEC OR LESS (2) THE AREA OF SOLDERING SHOULD BE OVER 75% |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST | SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON 30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED |
| 4.3 | HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 HR, THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HR FOR OTHER PROCEDURES | |
| 4.4 | HEAT TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 702 FOR 96 HOURS, AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM | THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED |
| 4.5 | COLD TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF -253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH | THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED |
| 4.6 | LIFE TEST (5,000 CYCLES) | WITHOUT LOAD: CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5,000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN. LOAD: AT RATING CONDITION (NON-INDUCTIVE LOAD) CONNECTION AND DISCONNECTION SHALL BE MADE 5,000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN. | (1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (Note: Source text shows 7N for disconnection force under load, but the range is provided as 0.8 to 2.0N. Using the specified range.) (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED |
| 4.7 | TEMPERATURE CYCLING TEST (5 cycles) | THE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE, AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 20N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN (BETWEEN TERMINALS) |
| 4.8 | COLD & HEAT SHOCK TEST (5 cycles) | THE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE, AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION & EXTRACTION FORCE: 3 TO 25N. CONTACT RESISTANCE: MAX.30M. INSULATION RESISTANCE: MIN.100 M. DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN (BETWEEN TERMINALS) |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina