Precision SHOU HAN TYPE-C 16P QTGM027 Connector Designed for Within Standard Atmospheric Conditions

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document outlines the specifications for the TYPE-C 16P QTGM027 connector from SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD. It details the product's ratings, operating temperature range, and performance under standard atmospheric conditions. The specification covers mechanical, electrical, and durability tests to ensure product quality and reliability.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: (Shenzhen)
Model: TYPE-C 16P QTGM027

Technical Specifications

Item	Test Conditions	Performance	Specification
RATING
		DC	20V 3A
PRACTICAL TEMPERATURE RANGE
			-30~80C
STANDARD ATMOSPHEIC CONDITIONS
	(1) Temperature		5C TO 35
	(2) Humidity		45% TO 85%
	(3) Pressure		86Kpa TO 106Kpa
MECHANICAL
CONNECTION FORCE	After connecting and disconnecting using standard plug gauge 3 times.		2.0Kgf
DISCONNECTION FORCE	After connecting and disconnecting using standard plug gauge 3 times.		0.6Kgf
TERMINAL STRENGTH	A static load of 0.1N/m(1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction.	No damage to the terminal such as cracks, looseness or play. Electrical and mechanical characteristics shall be satisfied.
ELECTRICAL
CONTACT RESISTANCE	Measured at small current (100mA or less), 1000Hz		40m
INSULATION RESISTANCE	Apply a voltage of 100V DC for 1 min to specified portions.		100M
DIELECTRIC STRENGTH	AC 100V rms(50~60Hz) for 1 min, trip current: 0.5mA. Tested between specified portions.	Without damage to parts, arcing or breakdown etc.
DURABILITY
SOLDERABILITY TEST	The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds.	(1) Solder wetting time shall be 3 seconds or less. (2) The area of soldering should be over 75%.
RESISTANCE TO SOLDERING HEAT TEST (REFLOW)	Preheat: Temperature on the copper foil surface should reach 180, 120s after the P.C.B entered into the soldering equipment.	Case without deformation, excessive looseness of terminals. Electrical characteristics shall be satisfied.
RESISTANCE TO SOLDERING HEAT TEST (REFLOW)	Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds.
RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON)	Bit temperature 3305, application time 30.5 seconds. However, excessive pressure shall not be applied to the terminal.	Case without deformation, excessive looseness of terminals. Electrical characteristics shall be satisfied.
HUMIDITY TEST	Stored at 402 and 90% to 96% humidity for 96 Hr, then maintained at standard atmospheric condition for 1 Hr.
HEAT TEST	Stored at 702 for 96 hours, then subjected to controlled recovery for 1 hour.	No damage on appearance. Mechanical and electrical characteristics shall be satisfied.
COLD TEST	Stored at -253 for 96 hours, then subjected to controlled recovery for 1 hour.	No damage on appearance. Mechanical and electrical characteristics shall be satisfied.
LIFE TEST	Without Load: Connection and disconnection for 5000 cycles at a speed of 10 to 25 cycles/min.
	With Load (Rating Condition, Non-Inductive Load): Connection and disconnection for 5000 cycles at a speed of 10 to 20 cycles/min.
	(1) Contact Resistance: 0.1 (2) Disconnection Force: 0.8 to 2.0N (3) Mechanical and Electrical Characteristics: Shall be satisfied.
TEMPERATURE CYCLING TEST	Subjected to 5 cycles of specified conditions, then allowed to remain in room ambient condition for 30 minutes.	No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max.30m. Insulation Resistance: Min.100 M. Dielectric Withstanding Voltage: 100VAC/min (between terminals).
TEMPERATURE CYCLING TEST	Temp(): 80 to -40 (details in figure)
COLD & HEAT SHOCK TEST	Subjected to 5 cycles of specified conditions, then allowed to remain in room ambient condition for 30 minutes.	No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max.30m. Insulation Resistance: Min.100 M. Dielectric Withstanding Voltage: 500VAC/min (between terminals).
COLD & HEAT SHOCK TEST	Temp(): 70 to -20 (details in figure)