SHOU HAN TYPE-C 6P 040 connector tested under mechanical load and electrical current for reliability
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
This document outlines the specifications for the TYPE-C 6P (040 new) connector from SHENZHEN SHOUHAN TECHNOLOGY CO., LTD. It details the product's performance under various conditions, including mechanical, electrical, and durability tests, ensuring suitability for a wide operating temperature range of -30~80C.
Product Attributes
- Brand: SHOUHAN TECHNOLOGY
- Origin: Shenzhen, China
- Model: TYPE-C 6P (040 new)
- Rating: DC 5V 3A
Technical Specifications
| Item | Test Conditions | Performance Specification |
| MECHANICAL | ||
| 1. CONNECTION FORCE | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 5-20N |
| 2. DISCONNECTION FORCE | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 6~20N |
| 3. TERMINAL STRENGTH | A static load of 0.1N/m (1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical, and mechanical characteristics shall be satisfied. | N/A |
| ELECTRICAL | ||
| 3.1 CONTACT RESISTANCE | Measured at small current (100mA or less) 1000Hz | 40m MAX |
| 3.2 INSULATION RESISTANCE | Apply a voltage of 100V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted. | 100M MIN |
| 3.3 DIELECTRIC STRENGTH | AC 100V rms (50~60Hz) for 1 min. Trip current: 0.5mA. (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted. Without damage to parts, arcing or breakdown etc. | N/A |
| DURABILITY | ||
| 4.1 SOLDERABILITY TEST | The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds. (1) Solder wetting time shall be 3 seconds or less. (2) The area of soldering should be over 75%. | N/A |
| 4.2 RESISTANCE TO SOLDERING HEAT TEST | Reflow soldering conditions: Preheat: Temperature on the copper foil surface should reach 180, 120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | N/A |
| Soldering iron method: Bit temperature 3305. Application time of soldering iron 30.5 sec. However, excessive pressure shall not be applied to the terminal. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | ||
| 4.3 HUMIDITY TEST | The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures. | N/A |
| 4.4 HEAT TEST | The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery measurement. There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | N/A |
| 4.5 COLD TEST | The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which. There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | N/A |
| 4.6 LIFE TEST | Without load: Connection and disconnection shall be made with the mating plugs and jacks for 3000 cycles at a speed of 10 to 25 cycles/min. | N/A |
| Load: At rating condition (non-inductive load). Connection and disconnection shall be made 3000 cycles at a speed 10 to 20 cycles / min. (1) Contact resistance shall be 0.1 (2) Disconnection force shall be 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied. | ||
| 4.7 TEMPERATURE CYCLING TEST | The jack shall be subjected to 5 cycles of the following conditions, and then shall be allowed to remain in room ambient condition for 30 minutes. There shall be no deformation or cracks in molded part. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 100VAC/min (between terminals). | N/A |
| Temperature profile: 70 (0.5h) -> 40 (1h) -> 0 (0.5h) -> -40 (0.5h) -> 70 (1h) -> -20 (0.5h) - 5 cycles. | ||
| 4.8 COLD & HEAT SHOCK TEST | The jack shall be subjected to 5 cycles of the following conditions, and then shall be allowed to remain in room ambient condition for 30 minutes. There shall be no deformation or cracks in molded part. Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 500VAC/min (between terminals). | N/A |
| Temperature profile: 70 (0.5h) -> 0 (1h) -> -20 (0.5h) - 5 cycles. | ||
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina