Electrical mechanical tested SHOU HAN TYPE-C 2P 90 2J 108 connector compliant with RoHS certification

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document specifies the requirements for a TYPE-C 2P 90 2J 108 connector, manufactured by Shenzhen Shouhan Technology Co., Ltd. It details the product's electrical, mechanical, and durability characteristics, ensuring compliance with RoHS standards and providing detailed test conditions and performance criteria for various parameters.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: (Shenzhen)
Certifications: RoHS

Technical Specifications

Item		Test Conditions		Performance
Mechanical	CONNECTION FORCE	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES	PLUG GAUGE 3	INSERTION FORCE	5~20N
Mechanical				DISCONNECTION FORCE	8~20N
	TERMINAL STRENGTH	A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION	1 0.1N/m(1kgf/cm). THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED
Electrical	CONTACT RESISTANCE	MEASURED AT SMALL CURRENT 100mA OR LESS 1000Hz	100 m A		40m MAX
	INSULATION RESISTANCE	APPLYA VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	100V DC 1 1 2 3		100M MIN
	DIELECTRIC STRENGTH	AC 100V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	AC 100V 50Hz/min 1 0.5mA, : (1) (2) (3)		WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC
Durability	SOLDERABILITY TEST	THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505FOR 50.5 SECONDS	1mm ,2505,5 0.5	(1) SOLDER WETTING TIME SHALL BE 3 SEC OR LESS (2) THE AREA OF SOLDERING SHOULD BE OVER 75%	3 75%
	RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING)	REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180.120S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605WITH IN 20 SECONDS.	: 180,120s : 260520		WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
	RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON METHOD)	BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL	3305, 30.5		WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
	HUMIDITY TEST	THE JACK SHALL BE STORED ATA TEMPERATURE OF 402AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES	40290~96% Hr 96 1		THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
	HEAT TEST	THE JACK SHALL BE STORED ATA TEMPERATURE OF702FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM	70296 1		THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
	COLD TEST	THE JACK SHALL BE STORED ATA TEMPERATURE OF-253FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH	-25396 1		THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
LIFE TEST	WITHOUT LOAD	CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN	Plug()1 10-255000	(1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	(1) 0.1 (2) 0.8~2.0N (3) :,
LIFE TEST	LOAD: AT RATING CONDITION NON-INDUCTIVE LOAD	CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN	()1 10-20 5000
TEMPERATURE CYCLING TEST	THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	Temp() 80 40 0 -40 1 cycle 8 hours 70 -20 Hours	INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS)	3N 20N 30m 100 M 100VAC
COLD&HEAT SHOCK TEST	THEJACKSHALLBESUBJECTEDTO5CYCLESOF THEFOLLOWINGCONDITIONSSHOWED INTHE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TOREMAININROOMAMBIENTCONDITIONFOR 30MINUTES	530	TEMP () 70 -20 1 cycle 1 hour 0.5 0.5 0.5 0.5 Hours	INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS)	3N 25N 30m 100 M 500VAC