connector SHOU HAN TYPE-C 6P LTH10.5 designed for stable DC 5V 3A operation and wide temperature range

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification document details the TYPE-C 6P LTH10.5 connector from Shenzhen Shouhan Technology Co., Ltd. It outlines the product's technical specifications, including electrical, mechanical, and durability performance, designed for reliable operation within a specified temperature and atmospheric range.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: Shenzhen, China
Product Name: TYPE-C
Part Number: TYPE-C 6P LTH10.5

Technical Specifications

Item		Test Conditions		Performance
RATING ()
				DC 5 V 3A	DC 5 V 3A
PRACTICAL TEMPERATURE RANGE ()
				-30~80C	-30~80C
STANDARD ATMOSPHERIC CONDITIONS ()
		(1) BETWEEN BODY AND CONDUCTOR	(1) 5~35	(1) 5C TO 35	(1) 5~35
		(2) BETWEEN CONDUCTORS NOT TO BE CONTACT	(2) 45%~85%	(2) 45% TO 85%	(2) 45%~85%
		(3) PRESSURE	(3) 86Kpa TO 106Kpa	(3) 86Kpa TO 106Kpa	(3) 86Kpa~106Kpa
MECHANICAL ()
1	CONNECTION FORCE	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES	PLUG GAUGE 3	0.52.0Kgf	0.52.0Kgf
2	DISCONNECTION FORCE	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES	PLUG GAUGE 3	0.82.0Kgf	0.82.0Kgf
3	TERMINAL STRENGTH	A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION	1 0.1N/m(1kgf/cm).	THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED
ELECTRICAL ()
3.1	CONTACT RESISTANCE	MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz	100 m A	40m MAX	40m MAX
3.2	INSULATION RESISTANCE	APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	100V DC 1 1 2 3	100M MIN	100M MIN
3.3	DIELECTRIC STRENGTH	AC 100V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	AC 100V 50Hz/min 1 0.5mA, : (1) (2) (3)	WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC
DURABILITY ()
4.1	SOLDERABILITY TEST	THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS	1mm ,2505,5 0.5	1SOLDER WETTING TIME SHALL BE 3 SEC OR LESS 2THE AREA OF SOLDERING SHOULD BE OVER 75%	13 275%
4.2	RESISTANCE TO SOLDERING HEAT TEST	REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180 .120 S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605 WITH IN 20 SECONDS.	:180,120s :260520	WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.2	RESISTANCE TO SOLDERING HEAT TEST	SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL	3305 30.5	WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.3	HUMIDITY TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES	402 90~96% Hr 96 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.4	HEAT TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM	70296 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.5	COLD TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH	-25396 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.6	LIFE TEST	WITHOUT LOAD CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN	Plug()1 10-255000	(1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	(1) 0.1 (2) 0.8~2.0N (3) :,
4.6	LIFE TEST	LOAD AT RATING CONDITION NON-INDUCTIVE LOAD CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN	()1 10-20 5000
4.7	TEMPERATURE CYCLING TEST	THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS)	3N 20N 30m 100 M 100VAC
4.8	COLD&HEAT SHOCK TEST	THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS)	3N 25N 30m 100 M 500VAC