SHOU HAN 10.0 HCHTZB6.3 USB Connector Operating Conditions and Mechanical Performance Specifications

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification outlines the requirements for the USB 10.0 HCHTZB6.3 product from SHENZHEN SHOUHAN TECHNOLOGY CO., LTD. It details the product's ratings, operating conditions, and performance criteria across mechanical, electrical, and durability tests.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO., LTD)
Part No: HCHTZB6.3
Project: USB 10.0
Contact: Tel: 0755-27597601, Fax: 0755-27597491

Technical Specifications

Item	Test Conditions	Performance Specification
RATING
Rated Value	DC 30V 1.5A
Operating Temperature Range	-25~85C	Within -25C~+85C
STANDARD ATMOSPHERIC CONDITIONS
Atmospheric Conditions for Measurements and Tests (Unless otherwise specified)	(1) Temperature: 5C to 35 (2) Humidity: 45% to 85% (3) Pressure: 86Kpa to 106Kpa
MECHANICAL
Connection Force	Measurement after connecting and disconnecting using standard plug gauge 3 times.	3.57Kgf MAX
Disconnection Force	Measurement after connecting and disconnecting using standard plug gauge 3 times.	1.02Kgf MIN
Terminal Strength	A static load of 0.1N/m(1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical, and mechanical characteristics shall be satisfied.
ELECTRICAL
Contact Resistance	Measured at small current (100mA or less) 1000Hz	30m MAX
Insulation Resistance	Apply a voltage of 100V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted	1000M MIN
Dielectric Strength	AC 500V rms(50~60Hz) for 1 min trip current:0.5mA (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted	Without damage to parts arcing or breakdown etc.
DURABILITY
Solderability Test	The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds.	(1) Solder wetting time shall be 3 seconds or less. (2) The area of soldering should be over 75%.
Resistance to Soldering Heat Test (Reflow Soldering)	Preheat: Temperature on the copper foil surface should reach 180, 120s after the P.C.B entered into the soldering equipment. Tallest Temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds.	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
Resistance to Soldering Heat Test (Soldering Iron Method)	Bit temperature 3305, application time of soldering iron 30.5 sec. However, excessive pressure shall not be applied to the terminal.	Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
Humidity Test	The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures.
Heat Test	The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery.	No damage on appearance. Mechanical and electrical characteristics shall be satisfied.
Cold Test	The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which.	No damage on appearance. Mechanical and electrical characteristics shall be satisfied.
Life Test (Without Load)	Connection and disconnection shall be made with the mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min.	(1) Contact resistance shall be 0.1 (2) Disconnection force shall be 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
Life Test (Load)	Connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min at rating condition (non-inductive load).	(1) Contact resistance shall be 0.1 (2) Disconnection force shall be 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
Temperature Cycling Test	The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes. Temp(): 70 (1 hour) -> 0 (0.5 hour) -> -20 (1 hour) -> 0 (0.5 hour).	No deformation or cracks in molded part. Insertion & extraction force: 3 to 20N. Contact resistance: Max. 30m. Insulation resistance: Min. 100 M. Dielectric withstanding voltage: 100VAC/min (between terminals).
Cold & Heat Shock Test	The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes. Temp(): 70 (0.5 hour) -> -20 (0.5 hour) -> 70 (0.5 hour) -> -20 (0.5 hour).	No deformation or cracks in molded part. Insertion & extraction force: 3 to 25N. Contact resistance: Max. 30m. Insulation resistance: Min. 100 M. Dielectric withstanding voltage: 500VAC/min (between terminals).