Electrical component SHOU HAN AF 180WJB13.7 USB connector rated for operation in harsh environments

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification outlines the requirements for the USB AF 180WJB13.7, a component designed for reliable performance within a specified temperature and atmospheric range. It details mechanical, electrical, and durability characteristics to ensure product quality and adherence to standards.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: Shenzhen, China

Technical Specifications

Item		Test Conditions		Performance
RATING
				DC Voltage	30V
				DC Current	1.5A
PRACTICAL TEMPERATURE RANGE
					-25~85C
STANDARD ATMOSPHEIC CONDITIONS
		(1) BETWEEN BODY AND CONDUCTOR	(1) 5~35	Temperature	5 TO 35
		(2) BETWEEN CONDUCTORS NOT TO BE CONTACT	(2) 45%~85%	Humidity	45% TO 85%
		(3) PRESSURE	(3) 86 Kpa~106Kpa	Pressure	86Kpa TO 106Kpa
MECHANICAL
1	CONNECTION FORCE	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES	PLUG GAUGE 3		40N MAX
2	DISCONNECTION FORCE	MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES	PLUG GAUGE 3		7N MIN
	TERMINAL STRENGTH	A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION	1 0.1N/m(1kgf/cm).	PERFORMANCE	THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED
ELECTRICAL
3.1	CONTACT RESISTANCE	MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz	100 m A		30m MAX
3.2	INSULATION RESISTANCE	APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	100V DC 1 1 2 3		1000M MIN
3.3	DIELECTRIC STRENGTH	AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODYAND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3)	PERFORMANCE	WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC
DURABILITY
4.1	SOLDERABILITY TEST	THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS	1mm ,2505,5 0.5	(1) SOLDER WETTING TIME	3 SEC OR LESS
				(2) THE AREA OF SOLDERING	OVER 75%
4.2	RESISTANCE TO SOLDERING HEAT TEST (REFLOW)	REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180.120S AFTER THE P.C. B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2505WITH IN 5 SECONDS.	:180,120s :25055	PERFORMANCE	WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.2	RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON)	SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL	3305 30.5	PERFORMANCE	WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.3	HUMIDITY TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 HR,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES	40290~96% Hr 96 1	PERFORMANCE	NO SPECIFIED DATA
4.4	HEAT TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM	70296 1	PERFORMANCE	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.5	COLD TEST	THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH	-25396 1	PERFORMANCE	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.6	LIFE TEST	CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN LOAD: AT RATING CONDITION NON-INDUCTIVE LOAD	()1 10-20 5000	(1) CONTACT RESISTANCE	0.1
		WITHOUT LOAD CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN	Plug()1 10-255000	(2) DISCONNECTION FORCE	0.8 TO 2.0N
				(3) MECHANICAL AND ELECTRICAL CHARACTERISTICS	SHALL BE SATISFIED
4.7	TEMPERATURE CYCLING TEST	THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	INSERTION EXTRACTION FORCE	3 TO 20N
		Temp() 100VAC/MIN(BETWEEN TERMINALS)		CONTACT RESISTANCE	MAX.30M
				INSULATION RESISTANCE	MIN.100 M
				DIELECTRIC WITHSTANDING VOLTAGE	100VAC/MIN
				PERFORMANCE	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART.
4.8	COLD&HEAT SHOCK TEST	THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	INSERTION EXTRACTION FORCE	3 TO 25N
		TEMP () 70 -20 0.5 1 cycle 1 hour 0.5 0.5 0.5 70 -20	Hours 8 hours	CONTACT RESISTANCE	MAX.30M
				INSULATION RESISTANCE	MIN.100 M
				DIELECTRIC WITHSTANDING VOLTAGE	500VAC/MIN
				PERFORMANCE	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART.