USB Connector SHOU HAN AF 180°WJZB13.0 Tested for Connection Force and Terminal Strength Reliability

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document outlines the specifications for the AF 180WJZB13.0 USB connector from Shenzhen Shouhan Technology Co., Ltd. It details the product's electrical, mechanical, and durability performance under various testing conditions, ensuring reliable operation within a specified temperature range.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: (Shenzhen)
Model: AF 180WJZB13.0
Contact Person (Drawn): (Li Chunfeng)
Contact Person (Check): (Luo Xiaojin)
Contact Person (Approved): (Zhong Huahua)
Tel: 0755-27597601
Fax: 0755-27597491

Technical Specifications

ITEM		TEST CONDITIONS		PERFORMANCE
MECHANICAL
MECHANICAL	CONNECTION FORCE		MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMESPLUG GAUGE 3	40N MAX	1
	DISCONNECTI ON FORCE		MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMESPLUG GAUGE 3	7N MIN	2
	TERMINAL STRENGTH		A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION 1 0.1N/m(1kgf/cm). THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED
ELECTRICAL
	CONTACT RESISTANCE		MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz 100 m A	30m MAX	3.1
	INSULATION RESISTANCE		APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED DC100V 1 MIN 100V DC 1 1 2 3	1000M MIN	3.2
	DIELECTRIC STRENGTH		AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODYAND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED DC 500V 1 MIN AC 500V 50Hz/min 1 0.5mA, : (1) (2) (3) WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC		3.3
DURABILITY
	SOLDERA- BILITY TEST		1 THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2305 FOR 30.5 SECONDS 1mm ,2305,3 0.5 2THE AREA OF SOLDERING SHOULD BE OVER 75% 75%	SOLDER WETTING TIME SHALL BE 3 SEC OR LESS 3	4.1
	RESISTANCE TO SOLDERING HEAT TEST		REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180 .120 S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK IN 5 TEMPERATURE OF 2305 WITH SECONDS. WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED :180,120s :23055 SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL 3305 30.5 WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	4.2
	HUMIDITY TEST		THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES 40290~96% Hr 96 1		4.3
	HEAT TEST		THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM 70296 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	4.4
	COLD TEST		THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH -25396 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	4.5
	LIFE TEST		CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN ()1 10-20 5000 WITHOUT LOAD CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN Plug()1 10-255000 LOAD AT RATING CONDITION NON-INDUCTIVE LOAD 1 CONTACT RESISTANCE SHALL BE 0.1 2 DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N 3 MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED (1) 0.1 (2) 0.8~2.0N (3) :,		4.6
	TEMPARATURE CYCLINGTEST		THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES 5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS) 3N 20N 30m 100 M 100VAC	4.7
	COLD&HEAT SHOCK TEST		THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS) 3N 25N 30m 100 M 500VAC	4.8