USB connector SHOU HAN AF 90° ZJDG ZB with practical temperature range minus 25 to 85 degrees Celsius

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document outlines the specifications for the USB AF 90ZJDG ZB, a product from SHENZHEN SHOUHAN TECHNOLOGY CO., LTD. It details the product's technical performance, including mechanical, electrical, and durability characteristics, along with testing conditions and acceptable performance criteria.

Product Attributes

Brand: SHENZHEN SHOUHAN TECHNOLOGY CO., LTD.
Origin: Shenzhen, China
Model: USB AF 90ZJDG ZB
Contact: Tel: 0755-27597601, Fax: 0755-27597491

Technical Specifications

Item	Test Conditions	Performance Specification
RATING
		DC 30V 1.5A
PRACTICAL TEMPERATURE RANGE
		-25~85C
STANDARD ATMOSPHEIC CONDITIONS
	(1) Temperature	5C TO 35
	(2) Humidity	45% TO 85%
	(3) Pressure	86Kpa TO 106Kpa
MECHANICAL
CONNECTION FORCE	After connecting and disconnecting using standard plug gauge 3 times.	3.57K MAX
DISCONNECTION FORCE	After connecting and disconnecting using standard plug gauge 3 times.	1.02Kgf MIN
TERMINAL STRENGTH	A static load of 0.1N/m (1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. No damage to terminal such as cracks, looseness or play. Electrical and mechanical characteristics shall be satisfied.	Satisfied
ELECTRICAL
CONTACT RESISTANCE	Measured at small current (100mA or less) 1000Hz	30m MAX
INSULATION RESISTANCE	Apply a voltage of 100V DC for 1 min to following portions: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted	1000M MIN
DIELECTRIC STRENGTH	AC 500V rms (50~60Hz) for 1 min Trip current: 0.5mA (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted. Without damage to parts, arcing or breakdown etc.	Satisfied
DURABILITY
SOLDERABILITY TEST	(1) The top of the terminals shall be dipped 1mm in the solder bath of 2305 for 30.5 seconds. Solder wetting time shall be 3 seconds or less. (2) The area of soldering should be over 75%.	Satisfied
RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING)	Preheat: Temperature on the copper foil surface should reach 180, 120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak in 5 seconds of 2305. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.	Satisfied
RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING)	(SOLDERING IRON METHOD) Bit temperature 3305 Application time of soldering iron 30.5 sec However, excessive pressure shall not be applied to the terminal. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.	Satisfied
HUMIDITY TEST	The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures.	Satisfied
HEAT TEST	The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to controlled recovery. There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied.	Satisfied
COLD TEST	The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to controlled recovery conditions for 1 hour. There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied.	Satisfied
LIFE TEST	(WITHOUT LOAD) Connection and disconnection shall be made with the mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min.	(1) Contact resistance 0.1 (2) Disconnection force is 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
LIFE TEST	(LOAD: AT RATING CONDITION (NON-INDUCTIVE LOAD)) Connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min.	(1) Contact resistance 0.1 (2) Disconnection force is 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
TEMPERATURE CYCLING TEST	The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes. Temp(): 70 (0.5h) -> -20 (0.5h). Cycle: 1 hour. Total cycles: 5. There shall be no deformation or cracks in molded part.	Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 100VAC/min (Between terminals).
COLD & HEAT SHOCK TEST	The jack shall be subjected to 5 cycles of the following conditions, and then shall be returned and allowed to remain in room ambient condition for 30 minutes. Temp(): 70 (1h) -> -20 (1h). Cycle: 1 hour. Total cycles: 5. There shall be no deformation or cracks in molded part.	Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 500VAC/min (Between terminals).