USB 10.0 SHOU HAN 10.0 4JCHT6.3 component with mechanical durability and standard atmospheric condition compliance

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification outlines the requirements for the USB 10.0 4JCHT6.3 product from Shenzhen Shouhan Technology Co., Ltd. It details the product's electrical, mechanical, and durability characteristics, along with standard atmospheric conditions for testing. The product is designed for use within a practical temperature range of -25~85C.

Product Attributes

Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
Origin: (Shenzhen)
Part Number: 4JCHT6.3
Project: USB 10.0

Technical Specifications

Item		Test Conditions		Performance
RATING
				DC 30V 1.5A
PRACTICAL TEMPERATURE RANGE
				-25~85C	-25C~+85C
STANDARD ATMOSPHERIC CONDITIONS
		(1) BETWEEN BODY AND CONDUCTOR	(1) 5~35
		(2) BETWEEN CONDUCTORS NOT TO BE CONTACT	(2) 45%~85%
		(3) PRESSURE	(3) 86Kpa TO 106Kpa
MECHANICAL
1		CONNECTION FORCE	PLUG GAUGE 3	3.57K MAX
2		DISCONNECTION FORCE	PLUG GAUGE 3	1.02Kgf MIN
3		TERMINAL STRENGTH	1 0.1N/m(1kgf/cm).	THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED
ELECTRICAL
3.1		MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz	100 m A	30m MAX
3.2		APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS	100V DC 1	1000M MIN
		(1) BETWEEN BODY AND CONDUCTOR	1
		(2) BETWEEN CONDUCTORS NOT TO BE CONTACT	2
		(3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	3
3.3		AC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA	AC 500V 50Hz/min 1 0.5mA, :	WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC
		(1) BETWEEN BODYAND CONDUCTOR	(1)
		(2) BETWEEN CONDUCTORS NOT TO BE CONTACL	(2)
		(3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED	(3)
DURABILITY
4.1		THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS	1mm ,2505,5 0.5	1SOLDER WETTING TIME SHALL BE 3 SEC OR LESS 2THE AREA OF SOLDERING SHOULD BE OVER 75%	13 275%
4.2	(REFLOW SOLDERING)	REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180 .120 S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605 WITH IN 20 SECONDS.	:180,120s :260520	WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.2	(SOLDERING IRON METHOD)	SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL	3305 30.5	WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.3		THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES	40290~96% Hr 96 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.4		THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM	70296 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.5		THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH	-25396 1	THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED
4.6		CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN (WITHOUT LOAD)	Plug()1 10-255000	(1) CONTACT RESISTANCE SHALL BE 0.1 (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED	(1) 0.1 (2) 0.8~2.0N (3) :,
		CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN (LOAD AT RATING CONDITION NON-INDUCTIVE LOAD)	()1 10-20 5000
4.7		THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS)	3N 20N 30m 100 M 100VAC
4.8		THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES	5 30	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS)	3N 25N 30m 100 M 500VAC