SHOU HAN TYPE-C16PIN
Price:
Negotiable
MOQ:
10
Delivery Time:
1工作日
Brand:
TYPE-C16PIN
Product Description
Product Overview
Product Name: TYPE-C 16PIN
Usage Temperature Range: -30~80℃
Standard Atmospheric Conditions for Testing: Temperature: 5℃ to 35℃; Humidity: 45% to 85%; Pressure: 86Kpa to 106Kpa.
Brand
SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD
Part Number
TYPE-C 16PIN
Material Code
RATING
Rated Voltage
30V
Rated Current
2A
Technical Specifications
| Item | Project | Test Conditions | Performance | Unit |
|---|---|---|---|---|
| MECHANICAL | CONNECTION FORCE | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 0.5-2.0 | Kgf |
| MECHANICAL | DISCONNECTION FORCE | Measurement shall be made after connecting and disconnecting using standard plug gauge 3 times. | 0.8~2.0 | Kgf |
| MECHANICAL | TERMINAL STRENGTH | A static load of 0.1N/m (1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical and mechanical characteristics shall be satisfied. | - | - |
| ELECTRICAL | CONTACT RESISTANCE | Measured at small current (100mA or less) 1000Hz | 10 | mΩ MAX |
| ELECTRICAL | INSULATION RESISTANCE | Apply a voltage of 100V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted | 100 | MΩ MIN |
| ELECTRICAL | DIELECTRIC STRENGTH | AC 100V rms (50~60Hz) for 1 min trip current: 0.5mA (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted | Without damage to parts arcing or breakdown etc. | - |
| DURABILITY | SOLDERABILITY TEST | The top of the terminals shall be dipped 1mm in the solder bath of 250±5℃ for 5±0.5 seconds. (1) Solder wetting time shall be 3 sec or less (2) The area of soldering should be over 75% | - | - |
| DURABILITY | RESISTANCE TO SOLDERING HEAT TEST (REFLOW) | Preheat: Temperature on the copper foil surface should reach 180℃.120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 260±5℃ with in 20 seconds. | Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | - |
| DURABILITY | RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON) | Bit temperature 330±5℃ Application time of soldering iron 3±0.5 sec. However excessive pressure shall not be applied to the terminal. | Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | - |
| DURABILITY | HUMIDITY TEST | The jack shall be stored at a temperature of 40±2℃ and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures. | - | - |
| DURABILITY | HEAT TEST | The jack shall be stored at a temperature of 70±2℃ for 96 Hours, and then it shall be subjected to the controlled recovery measurement. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | - |
| DURABILITY | COLD TEST | The jack shall be stored at a temperature of -25±3℃ for 96 Hours and then it shall be subjected to the controlled recovery conditions for 1 Hour after which. | There shall be no damage on appearance. Mechanical and electrical characteristics shall be satisfied. | - |
| DURABILITY | LIFE TEST (WITHOUT LOAD) | Connection and disconnection shall be made with the mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min. | - | Cycles |
| DURABILITY | LIFE TEST (LOAD) | At rating condition (non-inductive load) Connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min. (1) Contact Resistance Shall Be ≤ 0.1Ω (2) Disconnection Force Shall Be 0.8 to 2.0N (3) Mechanical and Electrical Characteristics Shall Be Satisfied | - | - |
| DURABILITY | TEMPERATURE CYCLING TEST | The jack shall be subjected to 5 cycles of the following conditions, and then shall return to room ambient condition for 30 minutes. | No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max.30mΩ. Insulation Resistance: Min.100 MΩ. Dielectric Withstanding Voltage: 100VAC/min (between terminals). | - |
| DURABILITY | COLD & HEAT SHOCK TEST | The jack shall be subjected to 5 cycles of the following conditions, and then shall return to room ambient condition for 30 minutes. | No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max.30mΩ. Insulation Resistance: Min.100 MΩ. Dielectric Withstanding Voltage: 500VAC/min (between terminals). | - |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Shenzhen ECER Network Technology Co., Ltd.
Location
Unit A2603, One Avenue (South Zone), Zhuoyue Meilin Center Plaza, No. 126 Zhongkang Road, Meidu Community, Meilin Subdistrict, Futian District, Shenzhen
Contact Person
Sellina