Matek F405 VTOL FC With Built In OSD And MicroSD Card 2 6S Input For FPV RC Multirotor Drones Flight Controller
Price:
$53.80 / piece
MOQ:
1 piece
Delivery Time:
Negotiable
Brand:
Matek
Product Description
| Product Features | |
| brand name | Matek |
| private mold | Yes |
| place of origin | Guangdong, China |
FC Specifications
* MCU: STM32F405RGT6, 168MHz , 1MB Flash
* IMU: ICM42688-P
* Baro: SPL06-001
* OSD: AT7456E
* Blackbox: MicroSD card slot
* 6x UARTs, 1x Softserial_Tx option(INAV)
* 12x PWM outputs
* 1x I2C
* 4x ADC (VBAT, Current, RSSI, Airspeed)
* 1x spare PINIO
* USB/Beep Extender with Type-C(USB2.0)
* Built in inverter on UART2-RX for SBUS input
* Switchable Dual Camera Input
FC Firmware
* ArduPilot: MatekF405-TE
* INAV: MATEKF405TE_SD (INAV 5.0 or newer)
PDB
* Input voltage range: 6.8~30V (2~6S LiPo)
* Sense resistor: 100A continuous, 220A peak
* 5x ESC power pads, total 100A continuous
* Support continuous load of up to 100A on ESC pad near the current sensor resistor
* Support continuous load of up to 30A & peak of 50A on each ESC pad of Quadcopter
* Battery Voltage divider 1K:20K (Scale 2100 in INAV, BATT_VOLT_MULT 21.0 in ArduPilot)
* Current Senor: 220A, 3.3V ADC (Scale 150 in INAV, 66.7 A/V in ArduPilot)
BEC 5V output
* Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
* Continuous current: 2 Amps
BEC 9V /12V output
* Designed for Video Transmitter, Camera, Gimbal ect.
* Continuous current: 2 Amps
* 12V option with Jumper pad
* for stable 9V/12V output, input voltage should > output voltage 1V
BEC Vx output
* Designed for Servos
* Voltage adjustable, 5V Default, 6V or 7.2V via jumper
* Continuous current: 8 Amps, 10A Peak
* for stable Vx output, input voltage should > Vx voltage 1V
BEC 3.3V output
* Designed for Baro / Compass module and external 3.3V peripherals
* Linear Regulator
* Continuous current: 200mA
Physical
* Mounting: 25 x 25mm-2mm, 35 x 35mm- 4mm
* Dimensions: 45 x 42 x 15mm
* Weight: 25g w/ USB/buzzer adapter
Including
* 1x F405-VTOL
* 1x USB(Type-C)/Beep (Passive buzzer) Extender 20cm JST-SH-6P to JST-SH-6P cable for USB extender.
* 1x 20cm JST-GH-4P to JST-GH-4P cable for I2C port
* 1x Rubycon ZLH 35V 470uF capacitor
* Dupont 2.54 pins (Board is shipped unsoldered)
* MCU: STM32F405RGT6, 168MHz , 1MB Flash
* IMU: ICM42688-P
* Baro: SPL06-001
* OSD: AT7456E
* Blackbox: MicroSD card slot
* 6x UARTs, 1x Softserial_Tx option(INAV)
* 12x PWM outputs
* 1x I2C
* 4x ADC (VBAT, Current, RSSI, Airspeed)
* 1x spare PINIO
* USB/Beep Extender with Type-C(USB2.0)
* Built in inverter on UART2-RX for SBUS input
* Switchable Dual Camera Input
FC Firmware
* ArduPilot: MatekF405-TE
* INAV: MATEKF405TE_SD (INAV 5.0 or newer)
PDB
* Input voltage range: 6.8~30V (2~6S LiPo)
* Sense resistor: 100A continuous, 220A peak
* 5x ESC power pads, total 100A continuous
* Support continuous load of up to 100A on ESC pad near the current sensor resistor
* Support continuous load of up to 30A & peak of 50A on each ESC pad of Quadcopter
* Battery Voltage divider 1K:20K (Scale 2100 in INAV, BATT_VOLT_MULT 21.0 in ArduPilot)
* Current Senor: 220A, 3.3V ADC (Scale 150 in INAV, 66.7 A/V in ArduPilot)
BEC 5V output
* Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
* Continuous current: 2 Amps
BEC 9V /12V output
* Designed for Video Transmitter, Camera, Gimbal ect.
* Continuous current: 2 Amps
* 12V option with Jumper pad
* for stable 9V/12V output, input voltage should > output voltage 1V
BEC Vx output
* Designed for Servos
* Voltage adjustable, 5V Default, 6V or 7.2V via jumper
* Continuous current: 8 Amps, 10A Peak
* for stable Vx output, input voltage should > Vx voltage 1V
BEC 3.3V output
* Designed for Baro / Compass module and external 3.3V peripherals
* Linear Regulator
* Continuous current: 200mA
Physical
* Mounting: 25 x 25mm-2mm, 35 x 35mm- 4mm
* Dimensions: 45 x 42 x 15mm
* Weight: 25g w/ USB/buzzer adapter
Including
* 1x F405-VTOL
* 1x USB(Type-C)/Beep (Passive buzzer) Extender 20cm JST-SH-6P to JST-SH-6P cable for USB extender.
* 1x 20cm JST-GH-4P to JST-GH-4P cable for I2C port
* 1x Rubycon ZLH 35V 470uF capacitor
* Dupont 2.54 pins (Board is shipped unsoldered)
Recommend Products
Customers Feedback
Packing&Shipping
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Shenzhen Huasheng Electronic Technology Co., Ltd.
Location
HB4082, Block B, Manha Market, 4th Floor, Extension Building, Sangda No.419 Building, Huaqiang North Road, Licun Community, Huaqiang North Subdistrict, Futian District, Shenzhen City, Guangdong Province, China
Contact Person
Chen