ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range + Omnidirectional Antenna For RC FPV Tinywhoop
Price:
$10.90 / piece
MOQ:
1 piece
Delivery Time:
Negotiable
Brand:
happymodel
Product Description
| Product Features | |
| Type | Antenna |
| Place of Origin | Guangdong, China |
| Age Range | 14 Years & up |
| Use | Vehicles & Remote Control Toys |
| Gender | Unisex |
| Model Number | EP1-RX |
Features
Notes:
Since the Official Perfect version of ELRS firmware has not been released yet, currently our PP_RX, EP1/EP2 RX and ES24TX
pre-loaded firmware are all beta versions, you can upgrade the official firmware when Official perfect target available.
More details: https://github.com/ExpressLRS/ExpressLRS
The Happymodel 2.4GHz ELRS nano series receiver is an open source program based on ExpressLRS, we have 3 types rx module released.
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and
SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.
On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the
same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that's too simple .
Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very
suitable for Tiny whoop because of the ultra light and Nano size.
Since the Official Perfect version of ELRS firmware has not been released yet, currently our PP_RX, EP1/EP2 RX and ES24TX
pre-loaded firmware are all beta versions, you can upgrade the official firmware when Official perfect target available.
More details: https://github.com/ExpressLRS/ExpressLRS
The Happymodel 2.4GHz ELRS nano series receiver is an open source program based on ExpressLRS, we have 3 types rx module released.
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and
SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.
On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the
same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that's too simple .
Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very
suitable for Tiny whoop because of the ultra light and Nano size.
Product Detail
Type: ISM
ESP8285 MCU
SX1280IMLTRT RF Module
Omnidirectional antenna
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
Working voltage: 5v
Weight: 0.42gram(without antenna)
Dimension: 10mm*10mm*6mm
Peak gain: 2.23dB
Bind procedure:
1.Supply power to the PP/EP1/EP2 rx, wait until the LED on the RX is off, immediately turn off the power, and then repeat again
the above steps. When the RX is powered on for the third time, the LED light will start to double-flash, which means that the RX
enters the binding mode
2.Insert the ES24TX module or other DIY 2.4G ELRS TX to Radio transmitter, and choose External RF mode to CRSF protocol, then you
can find ELRS menu from the Radio systems(Need to copy the ELRS.LUA file to the SD-Card tools first), Enter into ELRS and press
[Bind], the LED on the RX module will getting to be solid if bind successfully.
3.Receiver LED status meanings:
PP RX: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no
signal connection from the TX module
EP1/EP2 RX: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means
no signal connection from the TX module; LED flash fast means in WIFI hotspot mode, you can connect the WIFI of the RX and upgrade
firmware of the RX via visit 10.0.0.1(password:expresslrs)
ESP8285 MCU
SX1280IMLTRT RF Module
Omnidirectional antenna
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
Working voltage: 5v
Weight: 0.42gram(without antenna)
Dimension: 10mm*10mm*6mm
Peak gain: 2.23dB
Bind procedure:
1.Supply power to the PP/EP1/EP2 rx, wait until the LED on the RX is off, immediately turn off the power, and then repeat again
the above steps. When the RX is powered on for the third time, the LED light will start to double-flash, which means that the RX
enters the binding mode
2.Insert the ES24TX module or other DIY 2.4G ELRS TX to Radio transmitter, and choose External RF mode to CRSF protocol, then you
can find ELRS menu from the Radio systems(Need to copy the ELRS.LUA file to the SD-Card tools first), Enter into ELRS and press
[Bind], the LED on the RX module will getting to be solid if bind successfully.
3.Receiver LED status meanings:
PP RX: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no
signal connection from the TX module
EP1/EP2 RX: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means
no signal connection from the TX module; LED flash fast means in WIFI hotspot mode, you can connect the WIFI of the RX and upgrade
firmware of the RX via visit 10.0.0.1(password:expresslrs)
Item Packing
Ep1 RX Receiver x1
40mm Antenna x1
90mm Antenna x1
40mm Antenna x1
90mm Antenna x1
Detailed Images
|
If you are interested in this product, or if you need us to help you find a product, we can provide a one-stop service.You can
find me through the following contact information: |
|||||||
|
My email:
|
sales18@lxrcmodel.com
|
||||||
|
My Skype:
|
becky--rc-fans
|
||||||
|
My WeChat:
|
17140962579
|
||||||
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Shenzhen Huasheng Electronic Technology Co., Ltd.
Location
HB4082, Block B, Manha Market, 4th Floor, Extension Building, Sangda No.419 Building, Huaqiang North Road, Licun Community, Huaqiang North Subdistrict, Futian District, Shenzhen City, Guangdong Province, China
Contact Person
Chen