SHOU HAN TYPE-C 14PLC-H10.0
Price:
Negotiable
MOQ:
20
Delivery Time:
1 working day
Brand:
TYPE-C 14PLC-H10.0
Product Description
Product Overview
Project: TYPE-C
Part No: TYPC-14PLC-H10.0
Material Code: PRACTICAL
Rating: DC 20V 3A
Practical Temperature Range: -30~80C
Standard Atmospheric Conditions for Testing:
- Temperature: 5 to 35
- Humidity: 45% to 85%
- Pressure: 86Kpa to 106Kpa
BrandSHENZHEN SHOUHAN TECHNOLOGY CO.,LTD
OriginChina
Technical Specifications
| Item | Test Conditions | Performance | |||
|---|---|---|---|---|---|
| 1 | CONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | PLUG GAUGE 3 | 0.5-2.0Kgf | |
| 2 | DISCONNECTION FORCE | MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES. | PLUG GAUGE 3 | 0.8-2.0Kgf | |
| 3 | TERMINAL STRENGTH | A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION | 1 0.1N/m(1kgf/cm). | THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 3.1 | CONTACT RESISTANCE | MEASURED AT SMALL CURRENT 100m A OR LESS 1000Hz | 100 m A | 40m MAX | |
| 3.2 | INSULATION RESISTANCE | APPLY A VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | 100V DC 1 1 2 3 | 100M MIN | |
| 3.3 | DIELECTRIC STRENGTH | AC 100V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED | AC 100V 50Hz/min 1 0.5mA, : (1) (2) (3) | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC | |
| 4.1 | SOLDERABILITY TEST | THE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2505 FOR 50.5 SECONDS | 1mm ,2505,5 0.5 | (1) SOLDER WETTING TIME SHALL BE 3 SEC OR LESS | 3 |
| (2) THE AREA OF SOLDERING SHOULD BE OVER 75% | 75% | ||||
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST (REFLOW) | REFLOW SOLDERING CONDITIONS: PREHEAT:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH 180 .120 S AFTER THE P.C.B ENTERED INTO THE SOLDERING EQUIPMENT. TALLEST TEMPERATURE:TEMPERATURE ON THE COPPER FOIL SURFACE SHOULD REACH THE PEAK TEMPERATURE OF 2605 WITH IN 20 SECONDS. | :180,120s :260520 | WITHOUT DEFOR MATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.2 | RESISTANCE TO SOLDERING HEAT TEST (IRON) | SOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON30.5 SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL | 3305 30.5 | WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.3 | HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 Hr,THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES | 402 90~96% Hr 96 1 | ||
| 4.4 | HEAT TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF702 FOR 96 HOURSAND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MBASURBM | 70296 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.5 | COLD TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF-253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH | -25396 1 | THERE SHALL BE NO DAMAGE ON APPEARANCE MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | |
| 4.6 | LIFE TEST (WITHOUT LOAD) | CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 10000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN | Plug()1 10-2510000 | ||
| 4.6 | LIFE TEST (LOAD) | LOAD AT RATING CONDITION NON-INDUCTIVE LOAD CONNECTION AND DISCONNECTION SHALL BE MADE 10000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN | ()1 10-20 10000 | (1) CONTACT RESISTANCE SHALL BE 0.1 | 0.1 |
| (2) DISCONNECTION FORCE SHALL BE 0.8 TO 2.0N | 0.8~2.0N | ||||
| (3) MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED | :, | ||||
| 4.7 | TEMPERATURE CYCLING TEST | THE JACK SHALL BE SUB JECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | 5 30 | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 20N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 100VAC/MIN(BETWEEN TERMINALS) | 3N 20N 30m 100 M 100VAC |
| 4.8 | COLD&HEAT SHOCK TEST | THE JACK SHALL BE SUBJECTED TO5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE,AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES | 5 30 | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. INSERTION EXTRACTION FORCE:3 TO 25N CONTACT RESISTANCE:MAX.30M INSULATION RESISTANCE: MIN.100 M DIELECTRIC WITHSTANDING VOLTAGE: 500VAC/MIN(BETWEEN TERMINALS) | 3N 25N 30m 100 M 500VAC |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Shenzhen ECER Network Technology Co., Ltd.
Location
Unit A2603, One Avenue (South Zone), Zhuoyue Meilin Center Plaza, No. 126 Zhongkang Road, Meidu Community, Meilin Subdistrict, Futian District, Shenzhen
Contact Person
Sales