Light Testing Equipment

IEC61215-2-MQT14.2 Power Cord Torsion Tester For Torque Test After Retention Test. Introduction 1.1 Purpose This machine is mainly used for torque test after retention test. The test time is one minute and the torque value can be realized according to the standard configuration of different weights. 1.2 Standard IEC61215-2-MQT14.2 1.3 Technical parameter No Item Spec 1 Working position 1 2 Wire diameter 0-60mm 3 Torque range 0.1Nm,0.15Nm,0.35Nm,0.6Nm ,0.8 Nm,0.9 Nm 1.0 Nm,1

Flexible Lighting Cord Winding Tester Device Briefing: Flexible Lighting Cord Winding Tester meets requirements of Chapter 6.14 and Fig.3 of IEC60598-2-20:2002,GB7000.9-2008 standard;used for checking whether lighting string has enough mechanical strength. Technical Parameters: Repeat each of the following test 45 times for inspection on rigid lighting string’s qualification: a )60N pulling force acting on the bottom of the pipe not all of a sudden for 1 min. b )0.15N·m

IEC 60598-1 clause 9.2 expanded metal spacer , Tests for ingress of moisture Conform to IEC 60598-1 clause 9.2 Where connection is made by a plug or a similar device, then this shall be regarded as part of the complete luminaire and shall be included in the tests and similarly for any separate controlgear. For tests of 9.2.3 to 9.2.11, a fixed luminaire intended for mounting with its body in contact with a surface shall be tested with an expanded metal spacer interposed

IEC 60598-1 Annex K Temperature measurement- Double-walled cylinder Conform to IEC 60598-1 Annex K.1 The average ambient temperature in the draught-proof enclosure is taken to be the air temperature at a position near one of the perforated walls on a level with the centre of the luminaire. The temperature is usually measured by a thermocouple soldered to a metal mass of approximately 30 g shielded against radiation by a double-walled cylinder of polished metal open at the top

IEC 60598-1 Clause 8.15 Arrangement For Impact Test For Handlamps With a Handle Or Shell Of Flexible Material Product information: This test device is designed and manufactured according to the standard requirements of IEC 60598-1 clause 8.15.1 for handlamps having a handle or shell of flexible material, such as rubber or polychloroprene, compliance shall be checked by the following test. The parts of the handlamp which are gripped in normal use, are subjected to a pressure

IEC60598-1 clause 4.4.4 Fluorescent Lamp Holder Axial Force Tester / Lighting and Luminaries Test Equipment Product information: The test equipment is designed and manufactured according to IEC60598-1 clause 4.4.4 standard test item requirements, test content: axial pressure is applied to the G5 lamp holder of 15N, 30N axial pressure exerted on the G13 lamp holders, pressure holding time I minutes, then quit, deformation detection lamp holder shall not exceed the amount of

Toy Safety Sharp Edge Test Equipment/Tester, Sharp Edge Test Device Product introduction Sharp Edge Tester Sharp Edge Tester used to determine that metal or glass edges on toys and other articles intended for use by children under 8 years of age, and such edges exposed in normal use or as a result of reasonably forseeable damage or abuse of such toys and articles, present a potential risk of injury by laceration or avulsion. Standards: EN 71-1 ASTM F963 16CFR 1500 ISO 8124-1

IEC61215-2 Cord Anchorage Pull Tester for Testing Pulling Force Of Non-Detachable And Movable Power CordIntroduction1.1 PurposeThis tester is suitable for testing pulling force of non-detachable and movable power cord.It has the advantages of beautiful appearance, reasonable layout, good reliability and convenient maintenance. 1.2 StandardIEC61215-2-MQT14.2 1.3 Technical parameterNoItemSpec1Power supply220VAC±10%,50/60Hz2fuse5A3Power200W4Counter0～9999(×1,×10,×100)can be

IEC60598-1-clause10.2 Insulation resistance and electric strength Description If it is impossible to place metal foil in position on linings or barriers, the tests shall be made on three pieces of the lining or barrier which have been taken out and placed between two metal balls having a diameter of 20 mm, which shall be pressed together with a force of 2 N ± 0,5 N. Technical parameters: Model: KP-BP20 Ball Diameter:20mm Pressure: 2N

LED Aging Test Device / LED Temperature Rising Test Device / Light Source Aging Test Device Technical Function Description: LED Aging test device include: Aging room,intelligence test control cabinet,Programmable test power,Industrial PC and test software,which is to perform switch test and life test under a uniform temperature of LED lamp;can trace their situation of on and off,down time;can test specimens’ electrical parameter and historical report data;also can be sent to

Flexible Lighting Cord Winding Tester Device Briefing: Flexible Lighting Cord Winding Tester meets requirements of Chapter 6.14 and Fig.3 of IEC60598-2-20:2002,GB7000.9-2008 standard;used for checking whether lighting string has enough mechanical strength. Technical Parameters: Repeat each of the following test 45 times for inspection on rigid lighting string’s qualification: a ) 60N pulling force acting on the bottom of the pipe not all of a sudden for 1 min. b ) 0.15N·m

Luminaire Adjustment Test Device Product Info: Meet standards of GB/7000.1-2002 Chapter 4.14. And EN60598-1:2000 Function: Applied to testing adjustment device with soft cable and wire built in to check if its shares of conductor breakdown is in excess of 50% after continuous bending and if there is serious damage in insulation layer. Product feature:adopts PCL control and LCD panel operation with adjustable test angle and speed;power focal positioning;bend the axis and

Fluorescent Axial Force Tester Product Info: The test lamp holder should meet requirement of IEC60061-3 datasheet: Fluorescent with lamp hplder in place bear a pressure force in its axial direction applying to center of the lamp cap with 1minute -------G5 lamp holder 15N -------G13 lamp holder 30N -------Single-ended Fluorescent lamp holder(G23,G10q,GR8,ect) 30N -------Data of other lamp holder is still under consideration After test,space between holders should meet

Lamp String Flexible Rope Winding Test Device​ Equipment overview: Lamp string soft rope winding test device to meet the IEC60598-2-20:2002, GB7000.9-2008 the 6.14 chapters test requirements and figure 3 requirements made; this device mainly examine sealing lamp on whether have sufficient mechanical strength. Technical parameters: The conformity of the rigid lamp string is tested by turns over and over again with each test in the following 45 times: 60N) the tension of the A

Led Life Test System Technical Requirement 1. LED lighting product’s aging rack and control system: LED lighting product’s aging rack and control system consist of testing rack,on-site control system, remote monitoring system(see fig.1)which should have function to perform LED lighting product’s aging test,see below general requirement of the equipment: Fig.1 schematic diagram of control system 2. According to customer’s requirements and the lab size,reasonably arrange the

Lampholder Copper Contacts Security Thrust Test Device IEC60598-2-20 Lampholder Copper Contacts Security Thrust Test Device This specialized test apparatus is designed to verify the security of lampholder contacts, preventing contact shifting and ensuring live parts of lamp strings remain inaccessible due to friction-related issues. Product Information The test device evaluates lampholder contact security to prevent contact displacement and ensure that live parts of lamp

Draught Proof Enc​losure Items Description Standard Draught proof enclosure IEC 60598 Clause 12.4.1 and Annex D Volume: 1000H*1000D*1400Wmm Dimension: 1150*1300*1700mm Size can custom made. Skins space: 150mm Perforations: diameter 2mm Perforations area: 40% of whole skin IEC60598 GB7000

IEC60598-1 | Fluorescent Lamp Holder Axial Force Tester Luminaries Test Equipment Product information: The test equipment is designed and manufactured according to IEC60598-1 clause 4.4.4 standard test item requirements, test content: axial pressure is applied to the G5 lamp holder of 15N, 30N axial pressure exerted on the G13 lamp holders, pressure holding time I minutes, then quit, deformation detection lamp holder shall not exceed the amount of light foot length of 1 / 4.

IEC60558-1 Fig 6 Mandrel Tester Device Light Testing Equipment Product information This tester conforms to IEC60558-1 Fig6 and IEC60065 Fig14--16. The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish. A metal foil shall be placed closely to the surface of the specimen and subjected to a pull force of 1 N. The metal foil shall be so positioned that its borders are 20 mm away fromthe

Lampholder Copper Contacts Security Thrust Test Device Product information: The test apparatus is used to check security of lampholder contacts, avoid the lamp holder contacts shifting and the live parts of the lamp string becoming accessible which are caused by the frictions. Technical parameters: The test device is conform to the IEC60598-2-20 clause 113,Fig 2. It is made of stainless steel. Weights: one 15 N and one 30 N Test method: The incandescent lamp is removed and a