NH Fuse Switch Disconnector

Bar fuse switch , 3 Phase , 160 Amp , Pa66 V0 , DMC Cover , Plated Tin, With NH00 Fuse , apply for 185 MM Busbar System Introduction DNH18-160 / 185 stripe fuse type load disconnect switch can be used for 185mm bus system. After testing DNH18 product line is to meet customer requirements for high mechanical and heat resistance standards, with DNH18 products made tuv certification and product patents. Parameters Type DNH18-160A/185mm Fuse size NH00(NT00) Design working voltage

Vertical fuse switch , 3 Phase , 160 Amp , Copper T3 , NH Fuse type Vertical Switch Introduction DNH5-160 / 100 bar fuse-type disconnector has 3 pole separate sub-gate and 3-pole at the same time closing two operating agencies, directly installed in the 100mm busbar system. It will be three longitudinal arrangement of the single-pole fuse-type disconnector in one, each phase of a touch knife seat and a three-phase bus system connected to the outlet can choose a variety of

Vertical fuse switch , 3 Phase , 250 Amp , Copper T3 , Plated Tin, With NH1 Fuse Introduction DNH5-250A stripe fuse disconnector to meet the exchange of 50Hz, rated voltage to 660V, agreed to heat up to 250A, with load operation, the first current transformer and strip switch integration, with the upper and lower access to the line, Three-phase separate broken, but also three-phase at the same time break, etc., are widely used in complete sets of products and imported box

NH Fuse Switch Disconnector/strip type fuse switch disconnector/ fuse isolating switch/fuse base Introduction DNH5 vertical fuse circuit breaker designed for three-phase AC circuit power distribution and short circuit protection and overload design. ARS fuse disconnectors comply with PN-EN 60947-1, PN-EN 60947-3, IEC 60947-1, IEC 60947-3. DNH5 dedicated to the application of cable cabinets. DNH5 vertical fuse-type disconnector from the glass fiber reinforced, adding halogen

DNH5 Phase Fuse Switch 160A Vertical Type Vertical Break Disconnector And Isolator Introduction DNH5 series fuse-type disconnector (bar) The first current transformer and fuse switch integration, suitable for rated current 160A-630A, rated frequency 50 / 60HZ. The series of products modular, small size, the use of safe and reliable, low-voltage distribution cabinet in the application of a very high capacity density, showing a high economy, safety and strain, not only has a

HRC DNH5 Series 250A 3 Operation Vertical Design Fuse switch disconnector for switchgear Introduction DNH5 series of strip-type fuse-type disconnector to meet the exchange of 50Hz, rated voltage to 660V, agreed to heat up to 630A, with load operation. 1, DNH5 bar switch design is simple, multi-functional combination of convenience (such as the use of voltmeter, ammeter, fuse detection, remote control, joint assembly, etc.); 2, to reduce wiring, easy to increase the loop, an

HRC DNH5 Series 250A 3 Operation Vertical Design Fuse switch disconnector for switchgear Introduction DNH5 series of strip-type fuse-type disconnector to meet the exchange of 50Hz, rated voltage to 660V, agreed to heat up to 630A, with load operation, the first current transformer and bar switch integration, with the upper and lower inlet and outlet, Phase single break, but also three-phase at the same time break, etc., are widely used in complete sets of products and

Vertical fuse switch , 3 Poles , 630 Amp , Copper T3 , Plated Tin, With NH3 Fuse Introduction DNH5-630 bar fuse-type load disconnect switch (referred to as bar switch), mainly for high short-circuit current distribution circuit and motor circuit as a manual infrequent operation of the power switch, disconnector and emergency switch, and as a circuit short circuit Protection, DNH5-630 stripe type load disconnect switch (referred to as bar switch) technical performance

DNH5-400 / 3 Vertical Break Disconnector Switch 185mm Busbar System Introduction Current range of 160A ~ 630A, only two sizes, three-pole products, the internal need to configure the DIN standard fuse Transparent window design, you can view the internal fuse operation Visual breakpoints to ensure safe and reliable isolation Up and down the outlet, no derating The locking mechanism of the handle protects the product from misuse of unrelated personnel Complete the annex to meet

CE 3 Poles Copper T3 NH type vertical fuse switch Introduction DNH5 inline fuse switch disconnector with unique process engineering * Integrating of current transformer and fuse switch initiated domestically * With knife-edge entry and arc extinguishing equipment, it is safe for operation. * The isolating knife blade, full- range protection and semiconductor protection fusible core are optional * Fuse wire monitor and signal switch can be additionally mounted; with self