Formwork Tie Rod System

Cast iron water stop connector prevents water seepage along thread bars in concrete walls. Available in D15 (110mm) and D20 (160mm) sizes. Features reducing sleeve to block grout. Custom sizes and galvanized finish available. Cost-effective solution for water retaining structures.

High-strength formwork tie rod system for construction, rated at 145KN max load. Made from 45# steel (AISI 1045). Custom lengths up to 6m. Includes wing nuts, waler plates, and water stoppers. Ideal for concrete forming and lost part applications.

Durable galvanized formwork tie rod system for D15 and D20 bars. Features flanged wing nuts for direct load bearing, steel cones for easy removal, and water stoppers. SGS approved, customizable lengths, and reliable for concrete forming.

Durable cast iron slope plate with integrated wing nut for inclined formwork. Features 15° articulation for square plates, supports D15/D20 tie rods. Custom lengths available. Ideal for non-vertical formwork applications.

Cast super plate with integrated wing nut for inclined formwork. Available in square and round plates for D15 and D20 tie rods. Durable, efficient, and customizable lengths. Ideal for non-vertical formwork applications.

Cost-effective cast iron water stopper for retaining walls. Designed with Ø65 mm round sheet for D15 and D20 tie rods. Remains in situ after rod removal. Includes reducing sleeve to prevent grout ingress. Custom lengths available.

Ductile iron water stoppers prevent water seepage in retaining walls. Cast into concrete between tie rods, they remain after removal. Available in 15mm and 20mm bar diameters with customizable sizes. Galvanized for durability. Ideal for water-resistant structures.

Pressed waling plate 120x120x8mm for timber or steel walings. Embossed design increases rigidity. Galvanized finish resists corrosion. Compatible with D15 tie rods and wing nuts. Load capacity depends on contact area and bearing pressure. Custom sizes available.

High-strength 45# steel tie rod for formwork systems. 145KN max load, D15/D20 diameters, lengths up to 6m. Used with wing nuts, waler plates, water stops. Custom sizes available. Ideal for concrete embedding.

Cast iron water barrier prevents water seepage along thread bars in concrete walls. Cost-effective one-piece design. Available for D15 and D20 tie rods, 110mm or 160mm length. Custom sizes and galvanized finish optional.

Ductile cast iron tie rod with integrated water barrier nut prevents water seepage in retaining walls. Available in 15mm and 20mm diameters, galvanized finish. Custom sizes offered upon request. Ideal for waterproof concrete formwork.

Durable formwork tie rod system featuring D15 and D20 Dywidag thread bars, flanged wing nuts, and water stoppers. Ensures easy assembly, direct load bearing, and water-resistant walls. Custom lengths and galvanized options available.

Durable flanged wing nut with large pedestal for direct load bearing on walings. Available in 15mm and 20mm diameters. Compatible with hex wrench, thread bar, or hammer. Custom lengths available.

Durable cast iron wing nut with two lugs for securing tie rods in formwork systems. Compatible with 15-26mm bars, galvanized finish, and customizable sizes. Easy installation with hex wrench or hammer strike.

Durable galvanized formwork tie rod system with Dywidag thread, flanged wing nuts, and steel cones for easy removal. Available in D15 and D20 diameters, supporting custom lengths and high load-bearing. Ideal for efficient, reusable concrete forming.

Cost-effective cast iron water barrier combined with formwork tie rod for water retaining walls. Features Ø65mm round sheet, reducing sleeve to prevent grout ingress. Remains in situ after tie rod removal. Available for 15mm and 20mm rods. Custom lengths upon request.

Cold rolled 45# steel tie rod with max load 145KN. Weldable, bendable, and available in 15mm, 20mm, 26.5mm diameters. Custom lengths up to 6m. Includes wing nuts, water stops, and anchor plates. Ideal for slab formwork systems.

High-strength cold rolled tie rod system for wall formwork, made of Grade 45# steel (AISI 1045). Available in 15mm, 20mm, and 26.5mm diameters with max load up to 145KN. Weldable, bendable, and customizable lengths up to 6 meters. Includes wing nuts, water stops, and other accessories.

Pressed steel waler plate 120x120x6mm with embossed rigidity for timber or steel walings. Compatible with D15 tie rods and wing nuts. Load capacity depends on contact area and bearing pressure. Ideal for panel and timber wall formwork.

Durable cast iron slope plate with integrated wing nut for fastening inclined formwork. Articulation up to 15°. Compatible with D15 tie rods. Custom forged material available. Ideal for non-vertical formwork applications.