Flash Memory IC Chip

The OPA627SM is a precision high-speed Difet operational amplifier with ultra-low noise of 4.5 nV/√Hz and fast settling time of 550 ns to 0.01%. Ideal for precision instrumentation, audio circuitry, and data acquisition. Available in multiple packages with industrial and military temperature range options.

Low-voltage operational amplifier with rail-to-rail output, no crossover distortion, and low supply current (130 µA typ). Operates from -40°C to 125°C. Ideal for portable media players, HVAC, and motor control. ESD protected. Cost-effective for space-constrained designs.

High efficiency buck regulator with 500mA output, 42V input range, and 500kHz switching frequency. Features precision enable, adjustable soft-start, and thermal protection. Ideal for industrial and telecom systems.

Edge-triggered octal D-type flip-flop with 3-state outputs. Wide 2V to 6V operating range drives up to 15 LSTTL loads. Ideal for buffer registers, I/O ports, and bus drivers. Supports -55°C to 125°C. Available in multiple package options.

Octal buffer and line driver with 25-ohm series resistors for reduced noise. Features 12mA sink/15mA source, TTL/CMOS compatible, ESD protection, and partial-power-down Ioff support. Ideal for memory and clock drivers.

High-speed non-inverting octal buffer with three-state outputs, 9ns propagation delay at 5V. Drives up to 15 LSTTL loads. Wide temp range -55°C to 125°C. Ideal for bus line driving with significant power reduction vs LSTTL.

High noise immunity hex inverter with Schmitt-trigger inputs. Supports 2V to 6V operation, wide -55°C to 125°C range, and low power consumption. Ideal for industrial logic applications.

High-precision CMOS operational amplifier with auto-zeroing for ultra-low offset voltage (5μV max) and near-zero drift (0.05μV/°C). Features rail-to-rail output, low quiescent current (750μA), shutdown mode, and wide supply range 2.7V to 12V. Ideal for transducer, medical, and battery-powered instruments.

The OPA725AIDR is a very low-noise, high-speed CMOS op amp with 20MHz bandwidth and 30V/μs slew rate. Ideal for optical networking, active filters, and ADC buffers. Features rail-to-rail output, 0.0003% THD+N, and operates from 4V to 12V. Available in SOT23-5 and SO-8 packages.

Ultralow offset voltage of 10 μV and drift of ±0.1 μV/°C ensure high accuracy. Features 134 dB open-loop gain, 140 dB CMRR, and low 800 μA quiescent current per amplifier. Ideal for transducer, bridge, and precision instrumentation applications. Replaces OP-07, OP-77, and OP-177.

Quad 36V e-trim op amp with ±5 μV offset, 0.2 μV/°C drift, and 10 MHz bandwidth. Rail-to-rail I/O, 20 V/μs slew rate, and 1 nF capacitive load drive. Ideal for precision industrial and data acquisition systems. Specified from -40°C to +125°C.

Low noise 7.5 nV/√Hz op amp with 5 μV offset and 760 μA quiescent current. Rail-to-rail input/output, 5.5 MHz bandwidth. Ideal for audio, medical, and sensor applications. Available in SC70, SOT-23, and SOIC packages.

High-speed voltage-feedback CMOS operational amplifier with 200MHz GBW and 360V/us slew rate. Features low noise, rail-to-rail output, and thermal shutdown. Ideal for video, ultrasound, and optical networking. Operates on 2.5V to 5.5V supply. Available in SOT23-5 package.

High-speed rail-to-rail CMOS op amp with 38MHz bandwidth and 22V/µs slew rate. Low noise (5nV/√Hz) and THD+Noise of 0.0006%. Ideal for audio, video, and ADC driving. Single/dual/quad options. Operates from 2.5V to 5.5V. Specified from -40°C to 85°C.

Low-power CMOS operational amplifier with 1MHz bandwidth and 45µA supply current. Features rail-to-rail input/output, 0.5pA input bias, and operates on 2.1V to 5.5V. Ideal for battery-powered equipment, smoke detectors, and medical instrumentation. Available in SC70, SOT-23, and SOIC packages.

Precision 20MHz CMOS op amp with zero-crossover distortion, 150µV max offset, and 7nV/√Hz noise. Rail-to-rail I/O, 1.45mA quiescent current, and 1.8V to 5.5V supply. Ideal for sensor conditioning, ADC drivers, and test equipment.

The OPA2822E/2K5 is a dual, low-noise operational amplifier with 2.0nV/√Hz input noise, 500MHz bandwidth, and 90mA output current. Ideal for xDSL receivers, ADC drivers, and active filters. Supports single +5V to +12V supplies with low 4.8mA/ch current.

Ultra-low noise 4.5nV/√Hz high-precision op amp with 100μV max offset and 0.4μV/°C drift. Features 117dB open-loop gain and 100dB CMRR. Ideal for precision instrumentation, data acquisition, and professional audio. Fits OP-07/OP-05 sockets. Texas Instruments improved replacement for OP-27/OP-37.

Dual low-noise CMOS op amp with 5.5MHz bandwidth, 1mV max offset, and 0.2pA bias current. Ideal for sensor conditioning, audio, and active filters. Operates from 2.2V to 5.5V with 0.76mA/ch quiescent current. Available in MSOP-8 package.

The OPA2376AIDGKR is a dual low-noise operational amplifier with rail-to-rail input/output, 5.5MHz bandwidth, and 760µA quiescent current. Ideal for precision audio, medical instrumentation, and sensor conditioning. Available in space-saving VSSOP-8 package.