Digital I O Module

GE IC697MDL753 is a 5/48 Volt DC, 0.5 Amp Negative Logic 32-Point Output module Product information GE IC697MDL753 : The IC697MDL753 PLC output module is compatible with a wide variety of loads which include indicators, motor starters, solenoids and TTL interfaces. Due to the significant overall heat dissipation with each group of modules, the maximum current is set to 4 Amps. Each output can deliver a current rating exceeding its long-term rating. The ability of each output

GE IC660BBA105 12 Watts 1500V for one minute 115 VAC / 125 VDC 4-20 mA /0-24 mA Product information GE IC660BBA105 : The IC660BBA105 Current-source Analog 6 Output Block can be configured to hold the last output state, or a default state, and can receive output feedback and feedback time. The circuit transforms the signal to engineering values, and the block can work if there is CPU redundancy. This equipment also provides fault reporting that can be disabled if needed.

GE IC693CHS398 I/O Expansion baseplate 50 feet or 15 meters 25-pin D-shell female connector Product information GE IC693CHS398 : The IC693CHS398 baseplate is manufactured by GE Fanuc as part of Series 90-30 and it is an expansion baseplate. It is made to serve as part of a large-scale industrial control system. The IC693CHS398 expansion baseplate must always connect to the CPU baseplate in a PLC, but it can only connect to 1 CPU baseplate in total. However, it can connect to

GE IC200MDL940 24 V DC/ 120-240 Volts AC 10 milliamperes 20 cycles per minute Product information GE IC200MDL940 : The IC200MDL940 module is a VersaMax PLC relay output module manufactured by GE Fanuc. It is equipped with 16 output points. This module has Form A contact outputs and compatible of being used in Class 1, Division 2 rated environment in a temperature range between 0 and 60 degrees Celsius. It meets different environmental and industrial standards, including the

GE IC697CHS750 5-Slot Rear Mount I/O Rack 7.5 inches in depth 254 millimeters deep Product information GE IC697CHS750 : The IC697CHS750 is a 5-Slot Rear Mount I/O Rack by GE Fanuc for the series 90-70 PLCs. It is a rack used to connect with modules that belong to the IC697 PLC series. Racks with the same characteristics as this one are IC697CHS790 and IC697CHS791. The difference between them is the number of slots and the mounting orientation. To power this rack, there are

GE IC660BBD021 24/48 VDC Sink I/O 16 Circuit series 90-30 PLCs 3-wire solid sensors Product information GE IC697MDL653 : The IC660BBD021 has many configurable parameters, including output pulse test, configurable input filter time, output power up defaults, and output hold last state or default. The block is equipped with electronic short circuit and over temperature protection. It can detect a failed switch, open wire in tristate inputs, overload, or no load. Also,

GE IC697MDL653 32 points 24 VDC module 90-70 Series 0 to 2 milliamps 8 inputs each Product information GE IC697MDL653 : IC697MDL653 is designed to have both positive and negative logic characteristics; thus it is able to source current from the input device to the common user. The applicable input device is connected to the power bus and the module input. The following input devices are all compatible with the IC697MDL653: pushbuttons, limit switches, selector switches, and

GE IC693APU300 90-30 series of PLCs 1 MHz 5 V DV or 10 to 30 V DC RX3i system Product information GE IC693APU300 : The module can be configured to provide either 1 complex counter, 2 identical and complex counters, or 4 identical and independent simple counters. The module comes with 12 positive source inputs with an input voltage range of either 5 V DV or 10 to 30 V DC. Furthermore, you’ll find 4 positive source outputs, internal module diagnostics, and a removable terminal

GE IC693MDL634 24 Volts DC Series 90-30 PLC system 8 input points 11.5 to 30 volts DC Product information GE IC693MDL634 : he IC693MDL634’s Input Voltage Range goes from 0 to +30 volts DC, and its input current is of 7 mA (typical) at rated voltage. It functions with an on-state voltage of 11.5 to 30 volts DC and an off-state voltage of 0 to +5 volts DC. Its minimum on-state current is 3.2 mA and has a maximum off-state current of 1.1 mA. The IC693MDL634 has LED light

GE IC693CPU374 CPU module with a processor speed of 133 MH 240 KB 7.4 watts from 5V DC voltage Product information GE IC693CPU374 : General: The GE Fanuc IC693CPU374 is a single-slot CPU module with a processor speed of 133 MHz. This module is embedded with an Ethernet interface. Memory: The total user memory used by the IC693CPU374 is 240 KB. The actual size associated with program memory for the user primarily depends on the configured memory types, such as Register memory

GE IC693CPU341 GMC and GCM+ option modules 90-30 Series +5 VDC rated power supply Product information GE IC693CPU3411 : General: The IC693CPU341 module, a member of the GE Fanuc 90-30 Series, is a single slot CPU module which is equipped with 5 baseplates. It contains 4 remote and/or expansion baseplates in addition to the 1 CPU baseplate. It is equipped with an 80C188XL processor. Power: It runs at 20 MHz and requires a load of 490 milliamps from the +5 VDC rated power

GE IC693CMM301 0-32 devices can be linked on a Genius Bus Series 90-70 Product information GE IC693CMM301 : The IC693CMM301 Genius Communications bus uses a noise immune network so as to offer fast data transmission of real-time control data. Series 90-30 PLCs are able to connect with one another via a one Genius I/O serial bus with the aid of standard twisted pair, shielded cable, daisy-chained between devices, and terminated at both ends. It is important to use the proper

GE IC693APU305 PLCs made 12 points of positive logic inputs delivering 5 VDC or 10 to 30 VDC Product information GE IC693APU305 : The IC693APU305 module consists of 12 points of positive logic inputs delivering an input voltage of either 5 VDC or 10 to 30 VDC. Moreover, it has 8 positive logic outputs; 4 outputs with a current rating of 1 Amp and 4 configurable outputs with a rating of 0.5 Amps. All outputs are protected from damaged by a replaceable fuse. A dedicated

GE IC697CMM742 series 90-70 Type 2 15 pins that offer a choice of 10Base5 10Base2 Product information GE IC697CMM742 : The IC697CMM742 Ethernet interface (type 2) also includes preloaded firmware for simple installation; additionally, firmware is easy to upgrade and maintained indefinitely. This interface provides data exchange via configuration/logic-based Ethernet global data, TCP/IP communication via SRTP, full PLC programming/configuration, and comprehensive station

GE IC200MDL740 25-pin D-type terminal block connector 24-pin I/O connector Product information GE IC200MDL740 : IC693CBL317 which measures 10 feet/3 meters with an 8” external shield pigtail; and C693CBL320 which measures 3 feet/1 meters with an 8” external shield pigtail. A 24-pin I/O cable is used for building custom length cables and comes in three different kits: crimp wire receptacle, solder eyelet receptacle, and IDC (ribbon) receptacle Series 90 -30 PLCs GE Intelligent

GE IC693APU302 2-axis positioning module (APM) 24-pin I/O connector 3 feet/ 1 meter Product information GE IC693APU302 : The IC693APU302 can operate either in follower or standard mode. In follower mode, the module delivers high performance “electronic gearing,” which comes in handy for slave-master applications. The user can select a preferred mode in the configuration software. The axis positioning module can be accommodated by any CPU or remote baseplate in the 90-30

GE IC200ALG321 Analog Output module 12 bit voltage 0-10VDC 4 channel typical control/IO combinations Product information GE IC693ALG321 : Powerful and Reliable VersaMax controllers provide powerful, reliable operation. Modular, high-density VersaMax IO is versatile, compact, and affordable. Its scalable architecture and ease of use save time and money for both machine builders and end users. Media redundancy and hot swap capability increase uptime. A broad range Designed to

GE IC693ALG221 +5 VDC output to drive isolation circuitry 0 to 20 milliamps or 4 to 20 milliamps Product information GE IC693ALG221 : Input protection for the IC693ALG221 is sufficient to work with reduced performance with up to 200 V in common mode settings. This module also allows electrical isolation of external noise. All field connections require a good grade twisted, shielded instrumentation cable connected to the COM or GND. An LED indicator monitors power supply

GE IC693PCM301 single connector on the front of the PCM modules RS-232 connection Product information GE IC693PCAM301 : Specific: The IC693PCM301 can be programmed to operate as a one or two independent CCM ports, a CCM port, and a MegaBasic application using one serial port or a MegaBasic application using one or both serial ports. These modules are used for communicating with programming terminals, CRTs, bar code readers, scales, printers, ASCII devices, RTU master devices,

GE IC693ALG391 Series 90-30 Programmable Logic Controller 2-Channel 12 bits of binary Product information GE IC693ALG391 : IC693ALG391 receives negative data, it outputs the low end of the current range of 4 mA to 20 mA range. The software tends to reject any value more than 32767 keyed in the modules. The IC693ALG391 gives two output ranges that are 4 and 20 mA. These two output ranges have user information laid down to make sure that a count of 0 is equal to 4 mA and a