Communication Cable

Main contactors for high-power charging of AEV/EV-B, adopting 2-core standard cables equipped with Yakazi (7282-1020) connectors. No wire modification or adapter conversion required, delivering zero assembly tolerance error. The cable model complies with UL3266, 22AWG, constructed with XLPE halogen-free flame-retardant material. Its maximum operating temperature reaches 125°C, conforming to ELV automotive environmental regulations.

Integrated U-shaped slot with integrated emitter and receiver, slot width 5mm, capable of detecting thin blocking sheets ≥2×0.8mm; clearance tolerance ≤0.025mm, ultra-high positioning repeatability with zero offset for home position limit. Adopts 940nm DC infrared light source, resistant to strong workshop light and fluorescent lamp interference to avoid false triggering. Response time 0.17ms, maximum detection frequency up to 1kHz, suitable for high-speed assembly lines and

The connector is fitted with built‑in metal fixing screws at both ends. After tightening, it will not loosen due to vibration or pulling force, which is suitable for permanent fixed wiring, on‑board vehicle equipment and high‑vibration working environments. Adopting industrial‑grade galvanized full‑metal shielding, it can effectively suppress signal interference. Operating temperature range: −40 to 85 ℃. Withstand voltage: AC 1000V/ 1 min. Insulation resistance: ≥ 1000 MΩ.

JWPF connectors accommodate cables of 24 AWG to 22 AWG with an insulation outer diameter of φ1.4-1.7 mm. The housing comes with a dual locking system consisting of integrated housing lance terminal locks and internal retaining latches to prevent loosening under vibration conditions.

8-pin 8-contact Ethernet cable, compatible with multiple cable types including Cat5e, Cat6, Cat6A and Cat7. Its 90-degree bending design drastically saves installation space, ideal for tight mounting against cabinet backplanes with limited clearance. Equipped with 8 gold-plated phosphor bronze pins, it complies with TIA-568 standards: 1 Gbps gigabit transmission for Cat5e and stable 10 Gbps transmission for Cat6A. It supports power supply over Ethernet (PoE / PoE++).

The high-power DC power wiring harness is fully enclosed by a galvanized metal housing. The cable shielding mesh is connected to the housing with single-ended grounding to prevent signal wave interference with communication generated by drivers. It adopts turned gold-plated brass terminals featuring ultra-low contact resistance and small temperature rise during long-term current operation. Single pins support optional current:5-40 A, with a voltage withstand of 250 V DC and

1.25mm ultra-fine single-row connector for weak-current signals and low-power auxiliary power supply. Features locking structure to prevent disconnection and misinsertion with low mating force. 28 AWG wire, 500 mA operating current, -40 to +80℃ temperature range.

CAN, RS485 Signal Assembly + Power Supply and Fan Power Harness. Features 16/20 AWG wires, IP67 rating, -40 to +105℃ range, 300V rating, 3A current, 3m length, 8-pin wire-to-wire connectors with PVC insulation and tinned copper conductors.

High Voltage Box Connector Harness for energy storage with 6+8 pin wire-to-board design. Features silicone/XLPE insulation, tinned copper conductors, IP67 rating, and operates from -40 to +150℃. Supports 300V rated voltage with low-loss crown spring terminals (

High-current power + low-voltage signal integrated cable with 60A power pins and ≤1A signal pins. Features PA66 housing (UL94 V0), -40 to +150℃ range, and physical isolation to prevent interference between power and communication signals.

The contacts of USB‑BF are gold‑plated for anti‑oxidation performance, with a mating durability of ≥10,000 insert‑pull cycles. Built‑in M3 nuts inside the plug enable direct mounting onto equipment enclosures and industrial‑control panels with M3 screws. This USB 2.0 connector supports a transfer speed of 480 Mbps. It adopts a 5‑pin configuration (VBUS, D+, D‑, GND and shield‑GND), and the maximum power‑supply current is 1.5 A.

SF12 push-pull self-locking circular connector perfectly matches 3-wire PT100 platinum resistance sensors. It features a resistance value of 100 Ω at 0°C and complies with the IEC 60751 standard. The 3-wire design eliminates resistance errors caused by connecting cables. Built with a 1210 packaged thin-film platinum sensing element, the sensor boasts compact size and fast response speed. The cable adopts double shielding: inner aluminum foil layer plus outer tinned copper

HSD-4P-M to HSD-4P-F Adapter Cable features 100 Ω impedance, IP67 waterproof rating, and 360° metal shielding for anti-EMI. Withstands -40 to +125℃, compliant with LV214/USCAR standards. Ideal for automotive high-speed data, video transmission, and diagnostic interfaces.

Gold-plated phosphor bronze spring contacts mate with the inner conductors of coaxial cables for RF high-frequency signal transmission. The gold plating prevents oxidation and delivers low impedance, compatible with high frequencies up to 56 GHz. This ultra-fine RG1.13 cable features Teflon insulation with 7-strand twisted conductors, foamed PE/PTFE dielectric to maintain a constant 50Ω characteristic impedance. It adopts double-layer shielding: full coverage inner aluminum

Constructed from TPU/PUR materials. The static coiled cable can stretch to 3–5 times its original length and retracts automatically and promptly upon release. Its rated voltage stands at 300/500 V, compatible with low-voltage signal transmission and power supply. The cable maintains stable performance without fatigue after no less than 5 million stretching cycles.

Characteristic impedance of the product is 50Ω (75Ω customizable). Operating frequency: DC to GHz. It features low VSWR: standard ≤1.5. The cable boasts high voltage resistance and low leakage, with excellent RF signal isolation to suppress outward radiation interference. Matched with RG316 coaxial cable, it delivers high temperature resistance and low signal loss. An additional power wire is integrated to supply power to instruments simultaneously.

The D-Sub 26PIN connector adopts the industry-standard 3-row 26-pin layout with locking screws, enabling secure direct mounting on equipment panels. The J1939 Type 2 circular connector supports 12V/24V power supply for commercial vehicles and CAN bus communication.

This single‑end D‑Sub 25PIN splitter harness features one cable diverging into two branches. It terminates with a D‑Sub 15PIN signal channel and a standalone coaxial RF line with D‑Sub 9PIN connectors, enabling simultaneous transmission of serial control signals, analog video signals and high‑frequency RF signals. The communication cable adopts a double composite shielding structure to deliver robust resistance against EMI and RFI interference. Coaxial cables are available in

The product is equipped with an additional RJ45 network port, enabling communication between vehicle CAN bus, automotive Ethernet and standard IP networks. It supports high-speed DoIP diagnostics and network-based transmission of vehicle data.

The connector housing adopts PA66 material with flame rating UL94 V‑0. The cable is constructed from PUR material, featuring oil corrosion resistance, UV resistance and crack resistance under repeated bending.