SUS 304 Stainless Steel Programable Walk-In Chamber / Temperature Humidity Test Chamber
SUS 304 Stainless Steel Programable Walk-In Chamber / Temperature Humidity Test Chamber
Applications
Walk in test Chamber are used for various types of testing such as prototype evaluation, research & development testing, production testing, accelerated stress testing, reliability testing, failure analysis, and any other application where environmental simulation is needed.
1. All Walk-in Room Systems
a. Operate continuously in cooling mode.
b. Provide a hot gas by-pass system to automate capacity reduction when the room is at the set point temperature.
c. Are constructed with high quality components including: liquid line solenoids, liquid sight glass, dryers, strainers, and TX valves.
d. Contain Bock semihermetic (or equal ) compressors.
e. Contain LED Touchscreen (or equal) controls.
f. Comply with ASHRAE guidelines for piping and rating.
g. Are factory-assembled and tested.
h. Are simple to maintain because components are easily accessible and clearly labeled.
Up to 5 HP units can be mounted on the roof of the walk-in room. Larger units are installed on the floor next to the room.
Comprehensive piping diagrams, schematics, and charging data are available for our environmental walk-in rooms.
2. Main Technical Parameters
|
|
| 1.1 Workplace Volume |
IW 1500 × IH 1000 × ID 800 mm |
| 1.2 External Size | According to the design |
|
|
| 2.1 Temp. Range | -40ºC ~ 150ºC |
| 2.2 Temp. Deviation | ±2.0ºC |
| 2.3 Temp. Fluctuation | ±0.5ºC |
| 2.4 Tem. Uniformity | ±2.0ºC |
| 2.5Heating & Cooling Rate |
+20ºC ↓ -40ºC within 60min (no load, ambient temperature is 20ºC) |
|
|
| 3.1 Humidity Range | 20%R.H.~98%R.H |
| 3.2Temp. &Humidity Range |
|
| 3.3 Humidity Deviation |
±3.0%RH(>75%RH) |
| 3.4 Humidity Uniformity | ±3.0%RH |
| 3.5 Humidity Fluctuation |
±2.0%RH |
3. Walk-in Room Construction:
Rooms are constructed of Stainless Steel metal tongue and groove sectional panels. An assembled room has continuous steel perimeters to hold panels tightly in place.
Panel features include:
1) 100% insulation
2) Light weight for easy handling – average weight of the largest panel is 84 lbs.
3) Alignment pins for accurate fit.
4) Steel straps connect locking arms with locking pins on opposite sides of panels.
5) Cam-actuated locks ensure tight fits and accommodate frequent assembly / disassembly for relocating or enlarging the room.
Features
Walk-in, Drive-in Type
Stainless steel interior (or galvanized for savings)
Painted galvanized steel exterior for long life
MAP service doors are hinged (no tools or lifting)
Easy access to components
Reliable steam generator system for humidity applications
Sheathed electric heaters for safety and reliability
Adjustable vanes in supply grille allow directing of airflow as needed
Standards Implemented and met
GB-2423. 1-89(IEC68-2-1) Test A: Low Temperature Test
GB-2423. 2-89(IEC68-2-2) Test B: High Temperature Test
GJB360. 8-87(MIL-STD．202F) High Temperature Operating Life Test
GBJl50. 3(MIL-STD-810D) High Temperature Test
GJBl50. 4(MIL-STD-810D) Low Temperature Test
GB2423. 3-93(IEC68-2-3) Test Ca: method for steady-state damp heat test
GB2423. 4-93(IEC68-2—30) Test Db: Damp Heat Alternative Test
GJBl50. 9-93(MIL-STD-810D) Damp Heat Test
Specifications
High quality and reliability performance;
Controller:Touch screen, parameter and program control;
Competitive price and 12 months free parts warranty.
4. Walk-in Room Show
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.