0.62mm Height Top View 3030 1W High Power White LED Emitting Color changeable
0.62mm Height Top View 3030 1W High Power White LED Emitting Color changeable
This is our 0.62mm Height Top View 1W High Power White LED, the TOP 3030series is available in soft red, orange, yellow, green, blue and white. The LED has wide viewing angle and optimized light coupling by inter reflector. This feature makes the SMT TOP LED ideal for light pipe application. The low current requirement makes this device ideal for portable equipment or any other application where power is at a premium.
| Part No. | Chip Material | Lens Color | Source Color |
| DL-TOP3030WxxA-1W | InGaN | Yellow Diffused | White |
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ± 0.25mm (.010”) unless otherwise specified.
3. Specifications are subject to change without notice.
Features:
- Low profile.
- Colorless clear window.
- Super luminosity LED.
- Several colors available.
- Wide viewing angle.
- High performance.
- Small size (L×W×H: 3.0mm×3.0mm×0.52mm).
- Industry standard footprint.
- Computable with automatic placement equipment.
- Soldering methods: Reflow Soldering.
- The product itself will remain within RoHS compliant Version.
Applications:
- Reading lights (car, bus, aircraft).
- Portable (flashlight, bicycle).
- Mini-accent / Up lighters / Down lighters / Orientation.
- Bollards / Security / Garden.
- Cove / Under shelf / Task.
- Automotive rear combination lamps.
- Traffic signaling / Beacons / Rail crossing and Wayside.
- Indoor / Outdoor Commercial and Residential Architectural.
- Edge-lit signs (Exit, point of sale).
- LCD Backlights / Light Guides.
Absolute Maximum Ratings at Ta=25℃
| Parameters | Symbol | Max. | Unit |
| Power Dissipation | PD | 1000 | mW |
|
Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) |
IFP | 250 | mA |
| Forward Current | IF | 150 | mA |
| Reverse Voltage | VR | 10 | V |
| Junction Temperature | TJ | 125 | ℃ |
| Junction To Heat-Sink Thermal Resistance | RTH | 50 | K/W |
| Operating Temperature Range | Topr | -40℃ to +85℃ | |
| Storage Temperature Range | Tstg | -40℃ to +100℃ | |
| Soldering Temperature | Tsld | 260℃ for 5 Seconds | |
Electrical Optical Characteristics at Ta=25℃
| Parameters | Symbol | Min. | Typ. | Max. | Unit | Test Condition |
| Color Temperature | CCT | 2580 | --- | 6530 | K | IF=150mA |
| Luminous Flux * | Φv | 80 | --- | 110 | lm |
IF=150mA (Note 1) |
| Forward Voltage | VF | 5.80 | 6.30 | 6.80 | V | IF=150mA |
| CRI | Ra | 80 | --- | --- | IF=150mA | |
| Viewing Angle | 2θ1/2 | --- | 120 | --- | Deg |
IF=150mA (Note 2) |
| Reverse Current | IR | --- | --- | 50 | µA | VR=5V |
Notes:
- Luminous Intensity (Flux) Measurement allowance is ± 10%.
- θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
Reliability Test Items and Conditions:
The reliability of products shall be satisfied with items listed below:
Confidence level: 90%.
LTPD: 10%.
1) Test Items and Results:
| No. | Test Item | Test Hours/Cycles | Test Conditions | Sample Size | Ac/Re |
| 1 | Resistance to Soldering Heat | 6 Min |
Tsld=260±5℃, Min. 5sec |
25pcs | 0/1 |
| 2 | Thermal Shock | 300 Cycles |
H: +100℃ 5min ∫ 10 sec L: -10℃ 5min |
25pcs | 0/1 |
| 3 | Temperature Cycle | 300 Cycles |
H: +100℃ 15min ∫ 5min L: -40℃ 15min |
25pcs | 0/1 |
| 4 | High Temperature Storage | 1000Hrs. | Temp: 100℃ | 25pcs | 0/1 |
| 5 | DC Operating Life | 1000Hrs. | IF=150mA | 25pcs | 0/1 |
| 6 | Low Temperature Storage | 1000Hrs. | Temp: -40℃ | 25pcs | 0/1 |
| 7 | High Temperature/ High Humidity | 1000Hrs. | 85℃/85%RH | 25pcs | 0/1 |
2) Criteria for Judging the Damage:
| Item | Symbol | Test Conditions | Criteria for Judgment | |
| Min | Max | |||
| Forward Voltage | VF | IF=150mA | --- | F.V.*)×1.1 |
| Reverse Current | IR | VR=10V | --- | F.V.*)×2.0 |
| Luminous Intensity | IV | IF=150mA | F.V.*)×0.7 | --- |
*) F.V.: First Value.
Reel Dimensions
Carrier Tape Dimensions: Loaded quantity 3000 PCS Per reel.
Please read the following notes before using the product:
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
6. Caution in ESD
Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.