This is Flat Super Flux Piranha with Dome 4 Lead Super Yellow LED Indicators, its lens color is water clear , the emitting color and this size is changeable.

Please download specification: 

Features:

1. Fewer LEDs required.
2. Low profile.
3. Lowers lighting system cost.
4. Super flux output.
5. Viewing angle=120°.
6. The product itself will remain within RoHS compliant Version.

Descriptions:

1. This revolutionary package design allows the light designer to reduce the number of LEDs required and provide a more uniform and unique illuminated appearance than with other LED solutions.
2. The low profile package can be easily coupled with reflectors or lenses to efficiently distribute light and provide the desired light appearance.
3. The white LED which was fabricated using a blue LED and a phosphor, and the phosphor is excited by blue light and emits yellow fluorescence the mixture of blue light and yellow light results in white emission.
4. Utilizing advanced InGaN chip technology.

Applications:

1. Automotive exterior lighting.
2. Electronic signs and signals.
3. Special lighting application.

Package Dimension:

Notes:

1. All dimensions are in millimeters (inches).
2. Tolerance is ± 0.25mm (.010″) unless otherwise noted.
3. An epoxy meniscus may extend about 1.50mm (.059″) down the leads.
4. Specifications are subject to change without notice.

Absolute Maximum Ratings at Ta=25℃

Electrical Optical Characteristics at Ta=25℃

Notes:

1. Luminous Intensity (Flux) is measured with a light sensor and filter combination that approximates the CIE eye-response curve.
2. θ_1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device.

Typical Electrical / Optical Characteristics Curves

(25℃ Ambient Temperature Unless Otherwise Noted)

Reliability Test Items And Conditions:

The reliability of products shall be satisfied with items listed below:

Confidence level: 90%. LTPD: 10%.

1) Test Items and Results:

2) Criteria for Judging the Damage:

*) F.V.: First Value.

Please read the following notes before using the product:

• Over-current-proof

Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).

• Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

• Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.

• Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

• Caution in ESD

Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices equipment and machinery must be properly grounded.

Quality is our culture.All of our items are with excellent quality and reasonable price!
We will refund you in case of bad quality issue happens due to our product itself.

Please send email to us and will help you find your right product and give you best offer.

Tel: 86-755-82853859
Fax: 86-755-83229774
Email:wendy@doublelight.com.cn
Wechat:ywj199111103964
Skype:wendy@doublelight.com.cn