5mm Round Standard T-1 3/4 Type LED Emitting Diode 45 Deg Viewing Angle
5mm Round Standard T-1 3/4 Type Infrared Blue Transparent Emitting Diode Led
Features:
- Standard T-1 3/4 diameter package.
- Low forward voltage.
- Viewing angle=45°.
- Reliable and rugged.
- The product itself will remain within RoHS complaint Version.
Descriptions:
The device is spectrally matched with silicon photodiode and phototransistor.
Applications:
- Floppy disk drive.
- Optoelectronic switch.
- Camera.
- Free air transmission system.
- Video.
Bin Code TesTest Condition
| Part No. | Chip Material | Lens Color | Source Color |
|
DL-503IRTA-2IR45 |
GaAlAs |
Blue Transparent |
Infrared |
Notes:
- All dimensions are in millimeters (inches).
- Tolerance is ± 0.25 mm (.010″) unless otherwise specified.
- Protruded resin under flange is 1.00 mm (.039″) max.
- Specifications are subject to change without notice.
Package Dimension:
Absolute Maximum Ratings at Ta=25
| Parameters | Symbol | Max. | Unit |
| Power Dissipation | PD | 100 | mW |
|
Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) |
IFP | 1.00 | A |
| Forward Current | IF | 100 | mA |
| Reverse Voltage | VR | 5 | V |
| Operating Temperature Range | Topr | -40℃ to +80℃ | |
| Storage Temperature Range | Tstg | -40℃ to +85℃ | |
| Soldering Temperature | Tsld | 260℃ for 5 Seconds | |
Electrical Optical Characteristics at Ta=25℃
| Parameters | Symbol | Min. | Typ. | Max. | Unit | Test Condition |
| Radiant Intensity (Note 1) * | Ee | 5.5 | 9.0 | --- | mW/sr | IF=20mA |
| --- | 22.0 | --- | IF=100mA, tp=100µs, tp/T=0.01 | |||
| Viewing Angle (Note 2) * | 2θ1/2 | --- | 45 | --- | Deg | IF=20mA |
| Peak Emission Wavelength | λp | --- | 940 | --- | nm | IF=20mA (Note 3) |
| Spectral Bandwidth | △λ | --- | 50 | --- | nm | IF=20mA |
| Forward Voltage | VF | 0.80 | 1.20 | 1.50 | V | IF=20mA |
| --- | 1.60 | 1.80 | IF=100mA, tp=100µs, tp/T=0.01 | |||
| Reverse Current | IR | --- | --- | 10 | µA | VR=5V |
Notes:
- Luminous (Radiant) Intensity Measurement allowance is ± 10%.
- θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
- The dominant wavelength (λp) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device.
Typical Electrical / Optical Characteristics Curves(25℃ Ambient Temperature Unless Otherwise Noted)
Please read the following notes before using the product:
1. Over-current-proof
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
2. Repairing
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90% RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70% RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
3. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
4. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Company Introduction
HongKong Double Light Electronics Technology Co. Ltd was founded in 2005 as a professional LED manufacturer located in Shenzhen, China. We mainly produce a wide range of products with automatic production lines, which include THT LEDs, chip LEDs, LED displays, infrared LEDs, dot matrix, LCD backlights and LED lighting fixtures.
Please contact with me to help you find your right product and get your best price.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.