2000A Permalloy Clamp On Current Transformer With 120mm Jaw
S120 20K HZ BANDWIDTH 2000A CLAMP ON CURRENT TRANSFORMER
The S120 is a general purpose 2000A AC Clamp current probe transformer designed for use with DMMs, cable fault analysis and loggers instruments that have a current input. It has a 1000:1 or 2000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The S120 has an integral 2.5m or 5m lead terminated. The rounded jaw design on this clamp probe makes it well-suited for cable fault analysis applications where high accuracy and low phase shift and wide frequency.
Clamp-On Current Transformers GFUVE® maintains a large in-stock inventory of Clamp-On Current Transformers including AC, Micro Clamp and Clamp-On CT Accessories for most common applications. Below is a list of all clamp-on current transformers available through GFUVE material, however, not all models are in-stock.
Clamp-On Current Transformers are the one-handed operating solution for temporary energy audits or long-term energy studies. The GFUVE 1000A Clamp On Current Transformer is specifically designed to offer broad utility in a compact shape. These CTs deliver high-accuracy, high-sensitivity, versatility, and low phase shift.
APPLICATIONS
- Power quality analyzer(PQA)
- power and harmonic meters
- Energy meter calibrator
- Cable Fault Analysis
- Measuring around cable bundles
- Power load monitoring
- Earth resistance meter
- Large industrial loads
FEATURES
- Measurement range of 10mA to 2000A AC
- Improved ergonomic design & easy operation
- High content nickel metal permalloy core
- Frequency 10-2MHz
- Holding wire diameter: φ120mm
- Conforms to EN 61010, 600V CAT III
- Transformation ratio: 1000:1, 2000:5
- Low phase shift for power measurement
- Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters
- UL, CE mark
PARAMETERS
| Electrical parameters | |
|---|---|
| Ratio | 1000: 1 or 2000:5 (customized) |
| Accuracy class | 0.1%, 0.2%, 0.5% |
| Primary current | 0 - 2000A AC |
| Secondary current | 0-2A or 0 - 5A AC (customized) |
| Secondary voltage | 0-2V AC (customized) |
| Max. Cont. Input current | 2400A |
| Over voltage category | CAT III 600V |
| Output signal (AC current) | 500mA, 1A,2A,5A AC at nominal input current |
| Output signal (AC voltage) | 1V, 2V, 10V AC at nominal input current |
| Frequency range | 10Hz-2MHz |
| Dielectric strength | 3KV 50Hz/60Hz at 1 minute |
| Temperature range | -40°C to +55°C |
| Output | 2.5 meter cable with D01 connector or BNC |
| Max. voltage not insulated conductors | 600 V |
| Standard | EN 61010-1, EN 61010-2-032, IEC60044-1, IEC61869-2 |
| Installation | clamp type |
| Output mode | lead output(2.5m, 5m or 10m) |
| Accuracy (2000A Range) | |
| 0-10A | ≤0.5% |
| 10-100 | ≤0.2% |
| 100-2000A | ≤0.1% |
| Phase Shift(2000A Range) | |
| 0-10A | ≤0.5° |
| 10-100 | ≤0.2° |
| 100-2000A | ≤0.1° |
| Mechanical parameters | |
| Dimensions (L x W x H) (mm) | 178 x 290 x 30 |
| Weight (g) | 1200 |
| Holding wire diameter (mm) | φ120 |
| Max. jaw opening (mm) | 120 |
| Jaw color | Red & Grey |
| Material | PC+ABS, UL94 V0 |
PHOTO
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.